Kyocera TASKalfa 2550ci - Page 12

2MV-8
(16) Fusing is loose................................................................................................................1-4-49
(17) Image is out of focus. ..................................................................................................... 1-4-50
(18) Image center does not align with the original center. ..................................................... 1-4-50
1-4-4 Electric problems ................................................................................................................. 1-4-51
1-4-5 Mechanical problems...........................................................................................................1-4-59
1-4-6 Send error code ................................................................................................................... 1-4-61
(1) Scan to SMB error codes ............................................................................................... 1-4-61
(2) Scan to FTP error codes ................................................................................................ 1-4-62
(3) Scan to E-mail error codes ............................................................................................. 1-4-64
1-4-7 Error codes .......................................................................................................................... 1-4-66
(1) Error code....................................................................................................................... 1-4-66
(2) Table of general classification ........................................................................................ 1-4-67
(2-1) U004XX error code table: Interrupted phase B ..................................................... 1-4-70
(2-2) U006XX error code table: Problems with the unit ................................................. 1-4-71
(2-3) U008XX error code table: Page transmission error............................................... 1-4-71
(2-4) U009XX error code table: Page reception error .................................................... 1-4-71
(2-5) U010XX error code table: G3 transmission........................................................... 1-4-72
(2-6) U011XX error code table: G3 reception ................................................................ 1-4-74
(2-7) U017XX error code table: V.34 transmission ........................................................ 1-4-75
(2-8) U018XX error code table: V.34 reception.............................................................. 1-4-76
(2-9) U023XX error code table: Relay command abnormal reception ........................... 1-4-76
(2-10) U044XX error code table: Encrypted transmission ............................................... 1-4-76
1-5 Assembly and disassembly
1-5-1 Precautions for assembly and disassembly........................................................................... 1-5-1
(1) Precautions....................................................................................................................... 1-5-1
(2) Drum unit .......................................................................................................................... 1-5-1
(3) Toner ................................................................................................................................ 1-5-1
(4) How to tell a genuine Kyocera toner container................................................................. 1-5-2
1-5-2 Outer covers .......................................................................................................................... 1-5-3
(1) Detaching and refitting the front cover.............................................................................. 1-5-3
(2) Detaching and refitting the rear cover .............................................................................. 1-5-5
(3) Detaching and refitting the inner tray................................................................................ 1-5-6
(4) Detaching and refitting the eject rear cover...................................................................... 1-5-8
1-5-3 Paper feed section.................................................................................................................1-5-9
(1) Detaching and refitting the primary paper feed unit.......................................................... 1-5-9
(2) Detaching and refitting the MP paper feed roller and MP separation pad...................... 1-5-10
(3) Detaching and refitting the registration roller.................................................................. 1-5-12
(4) Detaching and refitting the registration cleaner .............................................................. 1-5-12
(5) Detaching and refitting the MP tray ................................................................................ 1-5-13
1-5-4 Developing section .............................................................................................................. 1-5-14
(1) Detaching and refitting the developing unit .................................................................... 1-5-14
1-5-5 Drum section ....................................................................................................................... 1-5-16
(1) Detaching and refitting the drum unit.............................................................................. 1-5-16
(2) Detaching and refitting the chager roller unit.................................................................. 1-5-16
1-5-6 Transfer/separation section ................................................................................................. 1-5-17
(1) Detaching and refitting the intermediate transfer unit..................................................... 1-5-17
(2) Detaching and refitting the secondary transfer roller unit ............................................... 1-5-17
1-5-7 Fuser section ....................................................................................................................... 1-5-18
(1) Detaching and refitting the fuser unit.............................................................................. 1-5-18