LEGRAND PDU - Page 504

June 2018
Legrand PDU User Guide 505
Setting Data Logging Measurements Per
Entry • 295
Setting Default Measurement Units • 95, 129,
136, 345, 347
Setting EAP Parameters • 308
Setting IPv4 Static Routes • 300
Setting IPv6 Static Routes • 303
Setting LAN Interface Parameters • 304
Setting Network Service Parameters • 312
Setting Non-Critical Outlets • 101, 103, 104
Setting NTP Parameters • 318, 320
Setting Outlet Power-On Sequence and
Delay • 100, 103
Setting the Alarmed to Normal Delay for
DX-PIR • 364
Setting the Authentication Method • 307
Setting the Automatic Daylight Savings Time
• 320
Setting the Baud Rates • 379
Setting the BSSID • 310
Setting the Cascading Mode • 15, 24, 31, 32,
33, 34, 35, 71, 139, 140, 141, 143, 149,
151, 155, 230, 231
Setting the Date and Time • 139, 180, 254,
266
Setting the HTTP Port • 312
Setting the HTTPS Port • 312
Setting the Inrush Guard Delay Time • 294
Setting the IPv4 Address • 299
Setting the IPv4 Configuration Mode • 298
Setting the IPv4 Gateway • 299
Setting the IPv4 Preferred Host Name • 298
Setting the IPv6 Address • 302
Setting the IPv6 Configuration Mode • 301
Setting the IPv6 Gateway • 303
Setting the IPv6 Preferred Host Name • 301
Setting the Maximum Number of Active
Powered Dry Contact Actuators • 297
Setting the Outlet Initialization Delay • 294
Setting the Outlet Power-On Sequence •
292
Setting the Outlet Power-On Sequence
Delay • 292
Setting the PDU-Defined Cycling Power-Off
Period • 293, 338
Setting the PDU-Defined Default Outlet
State • 293, 337
Setting the Polling Interval • 378
Setting the PSK • 307
Setting the Registry to Permit Write
Operations to the Schema • 435
Setting the SNMP Configuration • 314
Setting the SNMP Read Community • 315
Setting the SNMP Write Community • 315
Setting the SSID • 306
Setting the sysContact Value • 315
Setting the sysLocation Value • 316
Setting the sysName Value • 315
Setting the Time Zone • 266, 319
Setting the X Coordinate • 362
Setting the Y Coordinate • 363
Setting the Z Coordinate • 296, 363
Setting the Z Coordinate Format for
Environmental Sensors • 296, 363, 374
Setting Up an SSL/TLS Certificate • 139,
163, 168
Setting Up External Authentication • 139,
163, 171, 480
Setting Wireless Parameters • 306
Setting Your Preferred Measurement Units •
95, 129, 132, 136
Showing Information • 270
Showing Network Connections • 388
Showing Outlets Information • 64
Showing the Firmware Upgrade Progress •
75, 235
Single Login Limitation • 327
Slave Device Events in the Log • 481, 482
SmartLock • 255, 256
SmartLock and Card Reader • 84, 255
SNMP Gets and Sets • 264
SNMP Sets and Thresholds • 265
SNMPv2c Notifications • 159, 260
SNMPv3 Notifications • 159, 260, 261
Sorting a List • 85, 90, 100, 109, 116, 133,
135, 146, 209, 233, 234, 236
Special Character Requirement • 330
Specifications • 17, 395
Specifying Non-Critical Outlets • 286, 294
Specifying the Agreement Contents • 326
Specifying the CC Sensor Type • 362
Specifying the Device Altitude • 295
Specifying the EnergyWise Domain • 378
Specifying the EnergyWise Secret • 378
Specifying the SSH Public Key • 314, 346
Standard Attributes • 440
Start or Stop a Lua Script • 195, 202, 223,
224
Static Route Examples • 139, 142, 147, 300,
303
Step A
Add Your Legrand PDU as a RADIUS
Client • 440, 441, 453, 454
Step A. Determine User Accounts and Roles
• 429
Step B
Configure Connection Policies and
Standard Attributes • 440, 444
Configure Connection Policies and
Vendor-Specific Attributes • 453, 457
Step B. Configure User Groups on the AD
Server • 429
Step C. Configure LDAP Authentication on
the Legrand PDU • 430
Step D. Configure Roles on the Legrand
PDU • 431
Strong Passwords • 329