Lenze 8400 HighLine C Series - Page 1114

8400 HighLine | Parameter setting & configuration
Index
1114 L Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010
RPDO2 communication parameter (I-1401) 561
RPDO2 mapping parameter (I-1601) 563
RPDO3 communication parameter (I-1402) 562
RPDO3 mapping parameter (I-1602) 564
Running time (C00180) 625
Runtime measurement (C311) 636
S
Safety functions 373
Safety instructions 25
Safety module 373
SC
Depth of current setpoint filter (C00272)
634
Field precontrol (C00576) 670
Filter time const. DC detect. (C00280) 634
Freq. current setpoint filter (C00270) 633
Max. acceleration change (C00274) 634
max. output voltage (C00276) 634
Settings (C00079) 602
Tdn speed controller (C00072) 600
Tn field controller (C00078) 601
Tn field weakening controller (C00578) 670
Vp field controller (C00077) 601
Vp field weakening controller (C00577) 670
Width of current setpoint filter (C00271) 633
Scaling of physical units 826
SD10
Speed limit for feedback system 12 (error message)
485
SD11
Speed limit for feedback system 67 (error message)
485
SD3
Feedback system open circuit (error message)
485
SDO1 server parameter (I-1200) 557
SDO2 server parameter (I-1201) 558
Select control mode (C00007) 589
Select motor control (C00006) 588
Select. of BU oscillos. channels (C750) 702
Selecting the operating mode 105
Selection help 108
Selection of switching frequency 168
Sensorless vector control (SLVC) 106, 134
Serial number (C00204) 628
Service code - clamp threshold (C1763) 788
Service code - difference threshold UG (C1765) 788
Service code (C468) 661
Service code inverter charact. (C1751) 788
Service par. - clamp time (C1764) 788
Service Par. TCR factor (C1755) 788
Service Par. TCR function (C1752) 788
Servo control (SC) 106, 146
Setpoint arithmetic (C00190) 627
Setpoint precontrol filtering (C00275) 634
Setting the baud rate 506
Setting the error response 466
Setting the node address 506
Short overview of error messages 475
Signal flow
Sensorless vector control (SLVC)
145
Servo control (SC) 167
V/f characteristic control (VFCplus) 126
V/f control (VFCplus + encoder) 133
Signal source assignment 694
Signal type entry 826
Slip comp. (C00021) 594
Slip compensation 179
Slip regulator 130
SLVC
Cross current controller gain (C00986)
756
Field controller gain (C00985) 756
Tn torque controller (C265) 633
Software limit positions 389
Source dF21 (BU watchdog) (C292) 635
Speed control with torque limitation (SC) 149
Speed control with torque limitation (SLVC) 136
Speed encoder selection (C00495) 665
Speed feedback 107
Speed follower 393
Speed limitation (C00909) 750
Speed limits, defining 109
Speed override 434
S-ramp smoothing override 436
S-ramp time for jerk limitation 422
S-ramp time PT1 (C00182) 625
Status - brake output BD (C00117) 608
Status displays 453
Status of last device command (C00003) 587
Status word (C00150) 614
Status word (MCK) 371
Status word 2 (C00155) 615
Status-determining error (C00168) 622
Stop 430
Stop of the ramp function generator 193
Stop the ramp function generator 193
Stuff-bit error 542
Su02
Mains phase failure (error message)
478
Su03
Too frequent mains switching (error message)
478
Su04
CU insufficiently supplied (error message)
478
Switching cycles (C00177) 624
Switching freq. reduct. (temp.) (C00144) 613
Switching frequency 168
Switching frequency (C00018) 593
Sync correction increments (C01124) 764
Sync cycle time setpoint (C01121) 764
Sync phase position (C01122) 764
efesotomasyon.com - Lenze