Lenze 8400 HighLine C Series - Page 811

Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010 L 811
8400 HighLine | Parameter setting & configuration
Parameter reference
Table of attributes
C00107 DCB: Hold time 24468 5F94 E 1 UNSIGNED_32 1000 ;;
C00114
DIx: Polarity 24461 5F8D E 1 UNSIGNED_16 ;;
C00115
DI 1/2 & 6/7: Function 24460 5F8C A 2 UNSIGNED_8 1 ;;
C00117
Status - brake output BD 24458 5F8A E 1 UNSIGNED_8 1 ;
C00118
DOx: Inversion 24457 5F89 E 1 UNSIGNED_8 ;;
C00120
Motor overload threshold (I²xt) 24455 5F87 E 1 INTEGER_16 100 ;;
C00123
Device utilisat. threshold (Ixt) 24452 5F84 E 1 INTEGER_16 100 ;;
C00129
Brake resistance value 24446 5F7E E 1 UNSIGNED_16 10 ;;
C00130
Rated brake resistor power 24445 5F7D E 1 UNSIGNED_16 1 ;;
C00131
Thermal capacity of brake resistor 24444 5F7C E 1 UNSIGNED_16 10 ;;
C00133
Brake resistor utilisation 24442 5F7A E 1 UNSIGNED_16 1 ;
C00134
Ramp rounding - main setpoint 24441 5F79 E 1 UNSIGNED_8 1 ;;
C00136
Communication control words 24439 5F77 A 2 UNSIGNED_16 ;
C00137
Device state 24438 5F76 E 1 UNSIGNED_16 1 ;
C00138
Internal control signal 24437 5F75 A 3 UNSIGNED_16 ;
C00142
Auto-start option 24433 5F71 E 1 UNSIGNED_8 ;;
C00144
Switching frequency reduction
(Temp.)
24431 5F6F E 1 UNSIGNED_8 1 ;;
C00148
Config. group error 24427 5F6B E 1 UNSIGNED_16 ;;
C00150
Status word 24425 5F69 E 1 UNSIGNED_16 ;
C00155
Status word 2 24420 5F64 E 1 UNSIGNED_16 ;
C00158
Cause of controller inhibit 24417 5F61 E 1 UNSIGNED_16 ;
C00159
Cause of quick stop QSP 24416 5F60 E 1 UNSIGNED_16 ;
C00161
LS_SetError_x: Error number 24414 5F5E A 8 UNSIGNED_16 1 ;;
C00163
Logbook - binary elements 24412 5F5C A 2 UNSIGNED_16 1 ;;
C00164
Logbook - analog elements 24411 5F5B A 1 UNSIGNED_16 1 ;;
C00165
Error information 24410 5F5A A 2 VISIBLE_STRING ;
C00166
Error information text 24409 5F59 A 6 VISIBLE_STRING ;
C00168
Status-determining error 24407 5F57 E 1 UNSIGNED_32 1 ;
C00169
Logbook setting 24406 5F56 E 1 UNSIGNED_16 ;;
C00170
Current error 24405 5F55 E 1 UNSIGNED_32 1 ;
C00173
Mains voltage 24402 5F52 E 1 UNSIGNED_8 1 ;;;
C00174
Reduced brake chopper threshold 24401 5F51 E 1 UNSIGNED_8 1 ;;
C00175
Response for brake resistor control 24400 5F50 E 1 UNSIGNED_8 1 ;;;
C00177
Switching cycles 24398 5F4E A 5 UNSIGNED_32 1 ;
C00178
Elapsed-hour meter 24397 5F4D E 1 UNSIGNED_32 1 ;
C00179
Power-on time meter 24396 5F4C E 1 UNSIGNED_32 1 ;
C00180
Running time 24395 5F4B A 3 UNSIGNED_32 1 ;
C00182
S-ramp time PT1 24393 5F49 E 1 INTEGER_16 100 ;;
C00184
AutoFailReset repetition time 24391 5F47 E 1 UNSIGNED_16 1 ;;
C00185
AutoFailReset residual runtime 24390 5F46 E 1 UNSIGNED_16 1 ;
C00186
Max. no. of AutoFailReset procedures 24389 5F45 E 1 UNSIGNED_8 1 ;;
C00187
Current AutoFailReset procedures 24388 5F44 E 1 UNSIGNED_8 1 ;
C00188
AutoFailReset configuration 24387 5F43 E 1 UNSIGNED_8 1 ;;
C00189
Resp. too frequent AutoFailReset 24386 5F42 E 1 UNSIGNED_8 1 ;;
C00190
Setpoint arithmetic 24385 5F41 E 1 UNSIGNED_8 1 ;;
C00200
Firmware product type 24375 5F37 E 1 VISIBLE_STRING ;
C00201
Firmware 24374 5F36 A 6 VISIBLE_STRING ;
C00203
Product type code 24372 5F34 A 9 VISIBLE_STRING ;
C00204
Serial number 24371 5F33 A 9 VISIBLE_STRING ;
C00220
Accel. time - add. setpoint 24355 5F23 E 1 UNSIGNED_32 1000 ;;
Code Name Index Data Access
dec hex DS DA DT Factor R w CINH
efesotomasyon.com - Lenze