Luneau Technology Briot perception2 - Polishing

162 pages

Save Page as PDF

To Next Page

To Previous Page

Using your Edger...Usual procedure

3-66

LTO

3.2.9 POLISHING

Note : The presence and order of the icons displayed on the screen depend on the job data.

Screen 3-35 : Polishing Icons

With

Without

Main Page

Default Chapter5
- Table of Contents5
Installation9
Unpacking the Machine9
- Procedure9
Removing the Shipping Rails11
- Conditions11
Preparing the Bench12
- Machine Dimensions12
- Space and Drilling Required12
Water Connections13
- Specifications General13
  - Filtration Tank with Pump13
  - Pump13
- Pipe Connections13
  - Locate the Connecting Points13
  - Procedure14
Shipping Safeties16
- Remove the Shipping Safeties16
  - Procedure16
Electrical Connections17
- Specifications17
- Edger Wiring17
  - Procedure17
Starting the Edger18
- Procedure18
- Switching the Machine ON/OFF18
Precautions for Use19
Safety20
- Operator20
- Machine20
Recommendations21
Using Your Edger23
Presentation24
- Presentation of the Machine24
- Description of the Stations25
- Presentation of the Application Screen26
  - Work Interface26
  - Visual References27
Usual Procedure28
- Job Creation/Selection28
- Scanform32
- Gravitech™ Optical Plotter33
- Digiform41
- Presentation41
  - Deforming the Shape of a Job42
  - Pivoting the Shape of a Job43
- Drilling44
- Shape Creator Function48
  - Presentation48
  - Procedure48
- Blocking / Centering System51
- Edging55
- Polishing67
Special Case68
- Applying an Oversize68
- Edging the Left Lens with Different Parameters from69
  - Principle69
  - Procedure69
- Checking a Finishing before the Lens Is Edged70
Points to Remember79
Configuration81
Presentation of Configuration Menus82
- Presentation of the Configuration Menu Access Screen82
  - Screen Description82
  - Access / Exit82
- Presentation of the Personalisation Menu Access Screen83
  - Screen Description83
  - Access / Exit83
Adjustment of Setting Values84
- Preliminary Remarks84
- Procedure84
- Saving the New Configuration84
- Limits85
Correction of Frame and Lens Values86
- Preliminary Remarks86
- Procedure86
Configuration of General Operating Parameters88
- Principle88
- Screen Description88
- Access / Exit88
- Configuration of the Functions89
- Saving the New Configuration90
Configuration of Communication Parameters91
- Presentation91
  - Principle91
    - Screen Description91
  - Access / Exit91
Presentation of Maintenance Menus93
- Presentation of the Maintenance Menu Access Screen93
  - Screen Description93
  - Access / Exit93
- Presentation of the Maintenance Screen94
  - Screen Description94
  - Access / Exit94
Displaying the Components95
- Task List96
Maintenance of the Touch Screen Zone97
- Cleaning the Touch Screen97
Maintenance of the Scanform Unit98
- Cleaning the Scanform98
- Replacing a Stylus Head98
- Replacing the Frame Clip Tubes99
- Replacing the Centering Plate99
Maintenance of the Centering/Blocking System Zone100
- Cleaning the Bearing Surface100
- Cleaning the Lower Lens of the Collimator100
- Replacing the Main Fuse101
Regular Maintenance of the Edger102
- Replacing the Flexible Lens Clamp Adaptor Pad102
  - Preliminary Remarks102
  - Procedure102
- Replacing the Mill Bit103
- Replacing the Lens Feeler Tips105
- Dressing a Wheel107
  - Preliminary Remarks107
  - Procedure107
- Cleaning / Replacing the Removable Visor109
- Cleaning the Filters and Water Tank111
- Emptying the Water Tank111
Handling the Covers113
- Removing the Covers113
  - When113
  - How113
- Replacing the Covers113
Preventive Maintenance114
- Hints114
- Replacement Table for Standard Parts114
- Adjustments115
- Consulting the Statistics132
  - Presentation of the Statistics Menu132
    - Access/Exit132
  - Consultation Principles133
    - Incident Log133
    - General Operation of the Machine135
- Messages144
  - Types of Messages144
  - List of Messages144
Tests153
Presentation of Test Menus154
- Access / Exit154
- Typical Test Screen155
Operating Principle156
- Operating Principle of a Typical Screen156
- Operation of the Other Screens157
Characteristics 7.158
Technical Specifications158
- Characteristics159
- EC Standards161

Luneau Technology Briot perception2 - Polishing

Table of Contents

Related product manuals