Motion Control Engineering Nidec iControl - Page 448

Index-9
Layouts, iView screen layouts 8-30
LC01 Control Mode 9-31
LC12 KI Speed Offset Deceleration 9-31
LC14 Speed for min KI Deceleration 9-31
LC16 Speed for max KI Deceleration 9-31
LCD display, iBox 7-2, 7-3
LCD Fault message 6-53
LE03 Encoder Pulses 9-26
Learn encoder 9-69
Learn or Enter Motor or Encoder Data 9-69
LEARN SW TIMED OUT message 6-53
Learn Switch Timed Out Fault message 6-53
Learn switch, iBox control 7-11
Learn U/DNT1-5 and U/DETS Positions message 6-54
Learn U/DNT1-5 and U/DETS Speeds message 6-54
LEARN U/DTS POSITIONS message 6-54
LEARN U/DTS SPEEDS message 6-54
LEARNING EMPTY LOAD message 6-54
Learning empty load values message 6-54
LEARNING FULL LOAD message 6-54
Learning full load values message 6-54
Learning the
Building floor heights 4-2
Counterweight 3-11
Empty and loaded car weights 4-33
ETS and NTS Limit Switches 4-8
Load Weights 4-30
Learning the Safety Configuration 2-19
Level Down Sensor 4-4
Level Up Sensor 4-4
Leveling Accuracy specification 9-2
Leveling distance parameter 4-13
Leveling Overspeed Test 4-47
Leveling speed parameter 4-13
Leveling speed, adjusting for final stop 4-26
LI01, Type of Input 9-23
LI15, Direction Selection Inputs 9-25
LI20, Brake Switch Function 9-25
Light load anti-nuisance 4-30
Light Load Antinuisance message 6-54
Light load threshold 4-30, 4-33
LIMIT SW CHKSUM FAULT message 6-54
LIMIT SW LEARN FAULT message 6-54
Limit Switches Checksum Fault message 6-54
Limit Switches Learn Fault message 6-54
LM01 Motor Power 9-25
LM02 9-25
LM02 Motor Speed 9-25
LM03 Motor Current 9-25
LM04 Motor Frequency 9-25
LM05 Motor Voltage 9-25
LM07 Motor Torque 9-25
LN01 Traction Sheave Diameter 9-28
LN02 Gear Reduction Ratio 9-28
LN03 Roping Ratio 9-28
Load calibration on message 6-54
Load learn process activated message 6-54
Load learn process deactivated message 6-54
Load Weigher
Cross Head Deflection 1-3
Isolated Platform 1-3
Load weigher
Crosshead deflection 4-30
Empty load threshold 4-31
Heavy load threshold 4-30, 4-31
Isolated platform 4-30
Light load threshold 4-30
Overload threshold 4-30, 4-31
Rope tension 4-30
Load Weigher (Raw) test point, description 9-4
Load Weigher Adjustment 4-30
Load Weigher Balanced test point, description 9-4
Load Weigher Feedback test point, description 9-4
Load Weigher Sensor Adjustment 4-16
Load Weigher Signal test point, description 9-4
Loading parameters from a Configuration file 8-22
Lobby Peak Mode message 6-55
Local Area Network 8-12
LOCKOUT 2-30
Locks/Contacts Connections, iBox 6-112, 9-10
LOSS OF POS/SPD IND message 6-55
Loss of Position or Speed Indicators message 6-55
Low roll jerk parameter 4-12
LX11 Reference Splitting 9-34
M
MAC ADDRESS ERROR message 6-55
Mac Address Error message 6-55
MAC addresses
viewing on iBox 7-7
Mach Rm Insp message 6-56
Machine Rm Inspection message 6-56
Machine Room Heat Detectors Activated message 6-55
Machine Room Heat Detectors Deactivated message 6-55
Machine Room Inspection Disabled message 6-56
Machine Room Inspection Enabled message 6-56
Machine Room Inspection Operation message 6-56
Machine Room Inspection switch 7-11
Machine Room Inspection, running on 2-44–2-51, 3-9
Machine Room Stop Switch Open message 6-55
Magnetek
Clear faults 2-29
Keypad overview 2-29
Status indicators 2-30
Magnetek AC Drive Parameters Quick Reference 9-45, 9-52
MAIN FLOOR SMOKE message 6-56
Main Floor Smoke Sensor Recall message 6-56
Main Processor Board Quick Reference 6-96
MCE Loadweigher-Isolated Platform 3-5
MCE System hub 5-4
MD, Motor Drive relay indicator 9-11
MDRD, Motor Drive Redundancy indicator 9-11
Menu Bar 8-17
Menu tree, iBox LCD display 7-5
MF FORCING TIMED OUT message 6-56
MF1, MF2, DC power to motor field 9-12
Minimum Floor to Floor Time specification 9-2
Mode of Operation 5-13
Motion Start Fault message 6-56
Motion stopped due to IO toggle test message 6-56