Motion Control Engineering Nidec iControl - Page 449

Index-10 Manual # 42-02-2223
MOTION STOPPED-IO TST message 6-56
MOTOR CNTR PROOF FLT message 6-56
Motor Contactor Driver Proofing Fault message 6-56
Motor Contactor Proofing Fault message 6-56
Motor Contactor Status test point, description 9-4
Motor Current Limiting 4-14
Motor Field Forcing Timed Out message 6-56
Motor insulation 2-9
Motor Limit Protection Timer Elapsed message 6-57
MOTOR LIMIT TIMED OUT message 6-57
Motor Limit Timed Out message 6-57
MOTOR LMT TIMED OUT 2 message 6-57
Motor nameplate data 9-69
Motor Noise 4-15
Motor Overload Protection, verifying 2-51
Motor Triac active indicator 9-11
MOTR CNTR DRV PRF FLT message 6-56
MR HEAT DETECTORS message 6-55
MR INSP. DISABLED message 6-56
MR STOP SWITCH OPEN message 6-55
MRD, Motor Redundancy indicator 9-11
Multiple Input AC Board Quick Reference 6-103
Multiple Output Relay Board Quick Reference 6-105
N
Network Info 5-13
newlink quattro 9-45
Node Control 5-13
Normal and Emergency Terminal Switch Position Tests 4-53
Normal rate limited stop, adjusting for final stop 4-25
Normal Terminal Slowdown Limit (NTS) 4-8
Normal Terminal Switch Overspeed Tests 4-52
Nudging Front, NUDGING FRONT message 6-57
Nudging Operation message 6-57
Nudging Rear, NUDGING REAR message 6-57
Number of Cars in Group specification 9-2
Number of Stops specification 9-2
O
Online help, accessing 8-24
Orange cables 5-22
Oscilloscope
editing displays 8-39
OTHER CARS ALT FIRE message 6-57
Other Cars Alternate Fire Sensor Recall message 6-57
OTHER CARS MAIN FIRE message 6-57
Other Cars Main Fire Sensor Recall message 6-57
Over Current Power Threshold test point, description 9-4
Over Current test point, description 9-4
Over Current Threshold test point, description 9-4
Overload threshold 4-30, 4-31, 4-32
Overloaded car detection 4-30
Overshoot correction, Contract speed runs 4-14
Overshoot, adjusting for 4-7
Overspeed 1
description of 4-54
Overspeed 2
description of 4-54
P
PARAM CHNG-RESET CAR message 6-41
Parameter adjustment
using iView 8-19
using the iBox 7-4
Parameter entry screens 8-19
Parameters, Load from Configuration file 8-22
Parameters, Save to File 8-21
Passenger Operation, Passenger message 6-57
Pattern (Command) test point, description 9-4
Pattern (Directional) test point, description 9-4
Pattern (Phase) test point, description 9-5
Pattern (Raw) test point, description 9-5
Pattern (Region) test point, description 9-5
Pattern (Slew Limited) test point, description 9-5
Pattern Filtered test point, description 9-4
Pattern Interpolated test point, description 9-5
Peripheral hub 5-4
Photo Eye Antinuisance message 6-57
Pick voltage 2-41, 2-43
Pinging an IP address 5-11
pinning and unpinning windows in iView 8-33
PM gearless machines, synchronizing with AC drive 2-10, 2-
18
Position Bit test point, description 9-5
Position Cartop Offset Fault message 6-58
Position encoder resolution
verifying 3-10
Position iBox Connections 6-109, 9-6
Position Location Error Fault message 6-58
Position Margin 4-54
POSITION QUAD FAULT message 6-58
Position Quadrature Fault message 6-58
Position Quadrature Reversed Fault message 6-58
Position Speed Deviation Fault message 6-58
Position Speed Threshold Fault message 6-59
POSITION SYNC-FLOOR message 6-59
Position Synchronization Fault message 6-59
Position Synchronization Required at Floor message 6-59
Position Synchronization Required at Terminal message 6-59
Position Synchronized at Floor message 6-59
Position Synchronized at Terminal message 6-59
POSITION SYNC-TERMINAL message 6-59
POSITN QUAD RVRSD FLT message 6-58
POSITN SPEED DVTN FLT message 6-58
POSTN CARTP OFFST FLT message 6-58
POSTN LCTN ERROR FLT message 6-58
POSTN SPD THRSHLD FLT message 6-59
Power bus verification 5-3
Power line fluctuation 2-3
Power Transfer Input Activated message 6-59
Power Transfer Input Deactivated message 6-59
Power Transfer, POWER TRANSFER message 6-59
Power Up Position Synchronization Required at Terminal
message 6-60
PowerBack R6 Regenerative Drive
Parameters Quick Reference 9-44
Preparing for Final Adjustments 3-11
counterweight balancing 3-12
door operator 3-11