Netafim nmc-pro - Dosing by Quantity (Spread) Example

167 pages

Save Page as PDF

To Next Page

To Previous Page

NMC-PRO Installation Manual

14Page

ELECTRICAL INSTALLATION

3.3 Cold Start



Note: To perform a cold start or firmware upgrade, the controller must be in the “Technician” mode; refer to the

CONTROLLER ADVANCED SETTINGS - Operation Mode.

Main Page

Default Chapter3
- Table of Contents3
1 General Instructions9
- Basic Requirements for On-Site Preparation9
- Frequency Inverters9
- General Dimensions9
2 Unpacking and Mounting10
- Unpacking10
- Controller Mounting10
3 Power Supply Wiring11
- Main Power Wiring11
- Power Supply Options13
  - Power Supply Option a13
  - Power Supply Option B13
- Cold Start14
- Set Language, Time and Date15
- Electric Test15
- Firmware Upgrade16
  - Accessing the Application16
  - Running the Application17
4 Electrical Installation18
- Input/Output18
- Output Terminal21
- Input Terminals25
  - Wiring25
  - Analog Input Card27
- Expansion Unit Connection: Card Connection Options31
- Controller Setup40
- Controller Test Procedure43
- System Configuration Procedure46
5 PROGRAM Menu55
- Irrigation55
  - Setting Irrigation that Is Longer than 24H59
- Influence Program59
  - Using the Influences59
  - Setting the Influences59
- Water Run Time65
- Dosing66
  - Dosing Program66
  - Dosing Injection Methods67
- Ext. Condition68
  - Defining Analog Sensors69
- Agitator70
- Selector71
- Filter Flushing71
- Cooling72
- Misting74
- Water Heating75
6 MANUAL OPERATION Menu76
- Irrigation Pause76
- Start/Stop Program76
  - Start/Stop Valve77
- Filter Flushing77
7 Alarm Menu78
- Alarm Reset78
- History79
- Alarm Definition79
- Alarm Setting81
  - Analog Output Alarm Generation81
- Ec/Ph Alarm Definition82
- Ec/Ph Alarm Setting83
- Radio Sys. Alarm Definition83
- Radio Sys. Alarm View84
- SMS Subscription84
8 History Menu85
- Irrigation Log86
- RAD. / VPD Sum & Drain Log86
- Uncompleted Irrigation87
- Uncompleted Programs88
- Daily Irrigation88
- Irrigation Accumulation89
- AUX Meter Accumulation89
- Accumulation Reset89
- Filters90
- Cooling90
- Sensors Log91
- Event Log91
- System Log91
9 Test Menu92
- Relays92
- Digital Input93
- Analog Input94
- Temperature94
- Humidity95
- Hardware Check List95
- Analog Output Test96
10 Setup97
- Time & Date98
- System Setup98
- Temperature Calibration101
- Humidity Calibration101
- Ec/Ph Calibration102
  - Calibration of the Ec/Ph Monitor Transmitter102
  - Ec/Ph Transmitter Monitor & NMC-Pro Correlation104
- Pressure Calibration104
- Weather Station Calibration104
- Sensors Logging105
- Write to Data Plug105
- Read from Data Plug106
- Edit SMS Phonebook107
- SMS Setup107
- SMS Personal Message108
11 Configuration Menu109
- Device Delay Configuration110
  - Example of Device Startup & Shutdown Order110
  - Example of Stagger Valve Delay - Multiple Shifts111
- Pump Station Configuration112
- Valve Configuration113
- Valve Flow Rate114
- Water Meter115
- Dosing Channel Configuration116
  - Calibrating the Analog Dosing Valve117
- Dosing Configuration119
- EC Pre-Control Configuration120
- Drainage Configuration120
- System Pressure Configuration121
- Ec/Ph Range Definition121
- Pressure Sensor Range Definition121
- Cooling Configuration122
- Misting Configuration122
12 INSTALLATION Menu123
- Device Layout123
- Device List125
- Digital Input125
- Analog Input 1-2126
- Analog Output129
- Hardware Checklist129
13 Controller Advanced Settings130
- Pump Station Configuration130
- Multiple Water Meters131
  - Option a - Standard Use/Measurement131
  - Option B - Multiple Water Sources131
- Drain Meter Measurement132
  - Drainage Timing Option a132
  - Drainage Timing Option B133
- Various Dosing Channel Configurations134
- Dosing Configuration135
- Dual Ec/Ph Sensors136
- Hot Keys and Status Screens138
- Operation Mode138
14 Appendix A - Nmc-Pro Parts List140
15 Appendix B - Troubleshooting141
- Controller Malfunction141
- Burnt Fuse - in Case of Voltage141
16 Appendix C - Replacements and Additional Installations142
- Installing a 24 VAC Output Card142
- Removing a Card143
- Adding a Dry Contact Output Card143
- Adding an Input Card144
- LCD & Keyboard Replacement145
  - NMC-PRO: Old LCD & Keyboard Replacement145
  - NMC-PRO: New LCD & Keyboard Replacement146
17 Appendix D - Sensor Installation and Definition147
- EC - Ph Sensor Connection147
- Measuring Box Connection151
- Humidity Sensor Definition152
  - Outside Temperature/Humidity Sensor Connection153
  - Sensor Definition153
- Pyranometer Connection - Netafim1154
- Radiation Sensor Definition155
  - Radiation Sensor Configuration - Netafim155
  - Radiation Sensor Connection - Davis156
- Pressure Transducer Connection157
  - Analog Pressure Sensor Definition158
- Wind Direction Connection159
  - Wind Direction Sensor Definition160
  - Wind Speed Digital Input Definition160
- Sensor and Cable Specifications161
18 Appendix E- Technical Specifications162
- Technical Specifications162
- Controller Components162
19 Appendix F - Main Menu Tree166
20 Warranty167

Netafim nmc-pro - Dosing by Quantity (Spread) Example

Table of Contents

Other manuals for Netafim nmc-pro

Related product manuals