Omega DP41-B - Page 10

132 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Notes

viii

Table of Contents

Default Chapter3
- Table of Contents3
Introduction11
- Description11
- Features11
- Available Options and Accessories12
- Modes of Operation13
Unpacking14
- Section 2 Unpacking14
Safety Considerations16
Parts of the Meter17
- Front of the Meter17
- Figure 4-1 Front Detail17
- Rear of the Meter20
- Figure 4-2 Connector Label (AC Powered and DC Powered Detail)20
- Figure 4-3 Rear View21
- Table 4-1 Rear Connector Descriptions21
Setup22
- Conditions Requiring Dissassembly22
- Assembly/Disassembly22
Jumper Positions35
- Thermocouple Input35
- RTD Input35
  - For Rtds35
  - For RTD 10 Ohm Copper35
- Voltage/Process Value Input35
- Current/Process Value Input36
  - For 0-20Ma or 4-20Ma Range36
- Bridge Input36
- Signal and Power Input Connections39
- Setpoint Settings Menu Flowchart50
- Setpoint Settings Menu51
Section 10 Main Menu Configuration Flowchart52
SECTION 11 INPUT TYPE MENU FLOWCHART: (Input)53
Section 12 Input Type Selection54
- Input Type: (THERMOCOUPLE)54
- Input Type: (RTD)55
- Input Type: (DC VOLTAGE/PROCESS VALUE)56
- Input Type: (DC CURRENT)57
- Input Type: (BRIDGE)58
- Input Type: (POTENTIOMETER)59
SECTION 13 READING CONFIGURATION MENU and FLOWCHART60
Section 14 Reading Configuration Menu61
- Rd.sc.of Enter Reading Scale and Offset Submenu61
- Unt.tmp Enter Temperature Unit Selection Submenu65
- Dec Pt Enter Decimal Point Configuration Submenu65
- Filter Enter Filter Configuration Submenu66
- Fls.dsp Enter Flashing Display Control Submenu67
- Bright Enter Display Brightness Control Submenu67
Section 15 Input Configuration Flowchart68
Section 16 Input Configuration Menu: (Inp.cnf)69
- L IN.FRE Enter Power Frequency Selection Submenu69
- Ad.rate Enter Analog to Digital Rate Submenu70
- Mode Enter Input Mode Configuration Submenu70
- Table 16-1 A/D (Analog to Digital) Rate Option Table70
- Field Calibration for Cold Junction Compensation71
- In.sc.ofenter Input Scale and Offset Configuration Submenu72
- Table 16-2 Factory Calculated Scale Factor Table74
Section 17 Multi-Point Scale and Offset Menu Configuration Flowchart75
Section 18 Multi-Point Scale and Offset Menu Configuration: (Mp.sc.of)76
- Table 18-1 Conversion Number Table78
- Table 18-2 Reading/Input Scale & Offset Calculation Table79
Section 19 Output Configuration Menu Flowchart80
SECTION 20 OUTPUT CONFIGURATION MENU: (Out.cnf)81
- Ana.out Enter Output Configuration Menu81
- Ot.sc.of Enter Output Scale and Offset Configuration Submenu83
Section 21 Setpoint Configuration Menu Flowchart84
Section 22 Setpoint Configuration Menu85
Section 23 Alarm Configuration Menu Flowchart87
Section 24 Alarm Configuration Menu: (Al.cnfg)88
- AL 1. CNF Enter Alarm 1 Configuration Menu89
- AL 2.CNF Enter ALARM 2 CONFIGURATION MENU92
- AL Db93
- Num.dly Enter Number of Readings/Display Menu93
- Rst al93
- Enter Alarm Reset Control Menu93
Section 25 Communication Configuration Flowchart94
Section 26 Communication Menu Configuration: (Comm)95
- COM.PAR Enter Communication Parameters Submenu96
- Bus.fmt Enter Communication Bus Format Submenu97
- Dat.fmt101
- Modbus Enter Modbus Protocol Submenu104
- Addres Enter Address Selection Submenu105
- Sercnt Enter Serial Count Submenu105
Section 27 Display Color Selection Menu Flowchart106
Section 28 Display Color Selection Menu: (Color)107
- N.COLOR Enter Normal Color Submenu107
- SP1.CLR Enter Setpoint 1 Color Submenu107
- SP2.CLR Enter Setpoint 2 Color Submenu107
- AL1.CLR Enter Alarm 1 Color Submenu107
- AL2.CLR Enter Alarm 2 Color Submenu107
Section 29 Lockout (Access Security) Configuration Menu Flowchart108
Section 30 Lockout (Access Security) Configuration Menu109
Section 31 External Control Lines111
- Tare (Pin 1)111
- Peak (Pin 2)111
- Valley (Pin 3)112
- Swlin2 (Pin 4)112
- External Reset (Pin 5)112
- No Connection (Pin 6)112
- Digital Return (Pin 7)112
- Pin 8)112
- Display Hold (Pin 9)112
- LOCKOUT EEPROM (and 'MENU' BUTTON) (PIN 10)112
- RESET of ALARMS (PIN 11)112
- NONSTANDARD RX (PIN 12) and NONSTANDARD TX (PIN 13)113
- No Connection (Pin 14)113
- Ext (Pin 15)113
- Sp1 (Pin 16)113
- Sp2 (Pin 17)113
- Al1 (Pin 18)113
- Al2 (Pin 19)113
- Rtn Ext (Pin 20)113
Section 32 Troubleshooting114
- Error Mode Messages114
Section 33 Specifications118
- Current Input118
- Voltage Input118
- Potentiometer Input118
- Thermocouple Input118
- RTD Input119
- General119
- Table 33-1 Reading Rate121
- Figure 33-1 Meter Housing and Panel Cutout122
- Flashing Messgaes123
- Thermocouple Table123
- Table 33-2 ITS 90 Thermocouple Tables123
- RTD 10 OHM COPPER Table124
- RTD 385 Table124
- Table 33-3 RTD 10 OHM COPPER124
- Table 33-4 ITS 90 RTD 385124
- RTD 392 Table125
- Table 33-5 ITS 90 RTD 392 US125
Section 34 Factory Preset Values127
Section 35 Record Your Setup Values128
Approval Section130

Other manuals for Omega DP41-B

Operation Manual2 pages

Related product manuals

Preview: Omega DP41-W

Preview: Omega DP41-B Series

Omega DP41-B Series

Preview: Omega DP20

Preview: Omega DP606A

Preview: Omega DP25-S

Preview: Omega DP25B-S

Preview: Omega DP25B-E

Preview: Omega DPG1000B

Preview: Omega DPF20 Series

Omega DPF20 Series

Preview: Omega Platinum DP32Pt

Omega Platinum DP32Pt

Preview: Omega HHSL402SD

Omega HHSL402SD