How to resolve Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software cannot open the communications with current settings?
If you cannot open the communications with current settings in Omron Software, the setting of the routing table might be wrong. Reset the routing table of the Ladder Engine using the CX-Integrator so that it does not overlap with the network No. used by FinsGateway.
What to do if The data in the clipboard is not the I/O condition format in Omron WS02-SIMC1-E - V1.9 REV 02-2009?
If the data in the clipboard is not the I/O condition format in Omron Software, copy the I/O condition expression of correct format to the clipboard and try again.
Why Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software failed to create a PLC data folder?
If the Omron Software fails to create a PLC data folder, it could be due to low hard disk space or no access right. Check if the folder is read-only or the user is authorized to write.
Why Specified PLC type is not supported and Data Trace will not start in Omron WS02-SIMC1-E - V1.9 REV 02-2009?
If the specified PLC type is not supported and Data Trace will not start in Omron Software, the target PLC specifies other than CS/CJ/CP Series. Specify CS/CJ/CP Series as a target PLC.
What to do if Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software failed to connect to the PLC?
If Omron Software failed to connect to the PLC and the operation exited, it means it's not possible to communicate with the target PLC. Check the FINS address for the target PLC.
Why Omron WS02-SIMC1-E - V1.9 REV 02-2009 target PLC was switched from CX-Simulator to an actual PLC?
If the target PLC was switched from CX-Simulator to an actual PLC and the operation exited in Omron Software, the target PLC was changed while data replaying. The target PLC can not be changed while replaying data.
Why Omron Software failed to save the sampling data?
If Omron Software failed to save the sampling data, it could be due to: 1. Wrong path name 2. The file being used 3. Read-only file, or 4. Low disk space. Check if the path name is correct, if another application is using the file, if it is read-only or the user is authorized to write, and if disk space is enough.
How to resolve Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software communication error (received an error response)?
If you receive a communication error with Omron Software, it could be due to a wrong address specification or range of I/O memory for I/O conditions, or a wrong communications environment. Check the I/O conditions settings. Also, exit executing application programs excluding the CX-Simulator and try again.
Why Omron WS02-SIMC1-E - V1.9 REV 02-2009 Data Replay Tool failed to start?
If the Omron CX-Simulator Data Replay Tool fails to start, it might be caused by a wrong execution environment. Try closing all applications except the CX-Simulator and try again. If it still fails, uninstall and reinstall the CX-Simulator Software.
What to do if Omron WS02-SIMC1-E - V1.9 REV 02-2009 Debugger startup initialization error occurred?
If an error occurs while initializing the Debugger startup in Omron Software, it could be due to a wrong execution environment. Try closing all applications except the CX-Simulator and restarting the Debugger. If the problem continues, uninstall and then reinstall the CX-Simulator Software.
Outlines the manual's purpose and lists essential related documents for operation.
Provides a section-by-section summary of the manual's content.
Defines the target personnel and general safety guidelines for operating the PLC system.
Highlights critical safety warnings and potential hazards specific to CX-Simulator operation.
Provides precautions to observe when using the CX-Simulator in specific application contexts.
Explains the CX-Simulator's function, role in development, and core capabilities.
Details the architecture and components of the CX-Simulator software.
Compares CX-Simulator capabilities with actual PLC operations for effective debugging.
Highlights features that improve program debugging efficiency and user experience.
Lists compatible PLC models, CPU units, and computer requirements for CX-Simulator.
Provides a detailed comparison of CX-Simulator's behavior against actual CS/CJ-series PLCs.
Lists the necessary software prerequisites for installing and operating the CX-Simulator.
Step-by-step guide for installing the CX-Simulator software.
Instructions for removing the CX-Simulator software from the computer.
Explains the methods for starting CX-Simulator and connecting it to CX-Programmer.
Describes the layout and function of the main CX-Simulator windows.
Details how to configure system status, PLC units, UM settings, and clock parameters.
Covers the functions, menus, and operations within the Debug Console for debugging tasks.
Guides users on leveraging CX-Programmer for debugging, highlighting key operational differences.
Explains the various execution modes like Scan Run and Step Run for debugging programs.
Details the process of setting up Step Run, breakpoints, and I/O break conditions for precise debugging.
Covers debugging tasks, including execution time, status monitoring, and individual task execution.
Introduces serial communication capabilities, supported protocols, and hardware.
Provides instructions on setting up serial communication parameters for various units and ports.
Explains methods for connecting to external devices via serial communication.
Demonstrates debugging techniques using message display and serial data files.
Introduces network communication functions, supported protocols, and units.
Guides through setting up network communication parameters for various units.
Explains how to set up network connections and routing tables for FINS communication.
Provides examples for debugging network communications using display messages and local connections.
Explains how to connect the CX-Simulator with other applications for PLC debugging.
Describes connection methods, including coexistence on the same computer and network connections.
Outlines the functions for automating virtual external input creation and data management.
Explains the process of generating, running, and checking results using virtual external inputs.
Details methods like Command Log, Data Trace, Data Replay, and I/O Condition for input generation.
Explains how to run programs using Data Replay Tool, I/O Condition Tool, or a debugging ladder program.
Describes how to verify simulation results using time chart monitoring and Excel graphing.
Describes the fundamental operational flow of the CPU Unit within the CX-Simulator.
Explains cycle time calculation and highlights differences from actual CS/CJ/CP series PLCs.
Details the configuration and usage of I/O memory areas within the CX-Simulator.
Lists common errors encountered during CX-Simulator operation and their solutions.
Provides guidance on resolving connection, network, editing, and cycle time errors.
Introduces the tool for automating the creation of multiple data trace files.
Explains how to set up sampling addresses, files, and options for data trace recording.
To Next Page
General