What to do if Omron Software CX-Simulator Ladder Engine failed to gain the access rights?
If the Omron CX-Simulator Ladder Engine fails to gain access rights, another application program might be writing to the UM. After the application program being writing is completed, try again.
Why Omron WS02-SIMC1-E - V1.9 REV 02-2009 failed to switch the current UM and failed to gain the access rights of CX-Simulator Ladder Engine?
If the Omron CX-Simulator Ladder Engine fails to switch the current UM and fails to gain access rights, another application program might be writing to the UM. After the application program being writing is completed, try again.
How to fix Omron Software Alarms display application failed to start?
If the Omron Alarms display application fails to start, it might be due to a wrong environment for the Alarms display application. The event viewer is not working for Windows NT and the memo pad for Windows95/98. Change the OS settings so as to work.
What to do if The node address of FinsGateway unit is duplicated in Omron WS02-SIMC1-E - V1.9 REV 02-2009?
If the node address of FinsGateway unit is duplicated in Omron Software: 1. Change the FINS node address of the communications path in the [Work CX-Simulator] window. 2. Change the duplicated node address using network communications setting.
How to resolve Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software failed to create a header of FINS response (Fins_sendData)?
If the Omron Software fails to create a header of FINS response (Fins_sendData), it may be due to a wrong destination address of the FINS command. Check the destination of the FINS command sent by the Ladder Engine or application program or settings of the routing table.
What to do if an attempt was made to operate a FINS that was not for CPU Unit in Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software?
If an attempt was made to operate a FINS that was not for CPU Unit in Omron Software, it may be due to a wrong destination address of the FINS command. Set "0" to the FINS unit address for the destination of the application that sent the FINS command.
Why Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software program is running and I cannot set a start point?
If the Omron Software program is running, you cannot set a start point because you tried to set a start point while running the program. A start point can be set only when stopping (Program mode).
Why Omron WS02-SIMC1-E - V1.9 REV 02-2009 Software unexecuted Cyclic task cannot be changed to WAIT mode?
If an unexecuted Cyclic task cannot be changed to WAIT mode in Omron Software, it is because you tried to change a Cyclic task in INI to WAIT mode. Try again after executing the program.
How to fix Omron Software Communication error (communications timeout)?
If a communications timeout error occurs in Omron Software, it means a timeout occurred in a response from the Ladder Engine. If the cycle time of the Ladder Engine is too long, use synchronous processing in the virtual cycle time. Check if the target FINS address is the same as that of the Ladder Engine.
Outlines the manual's purpose and lists essential related documents for operation.
Provides a section-by-section summary of the manual's content.
Defines the target personnel and general safety guidelines for operating the PLC system.
Highlights critical safety warnings and potential hazards specific to CX-Simulator operation.
Provides precautions to observe when using the CX-Simulator in specific application contexts.
Explains the CX-Simulator's function, role in development, and core capabilities.
Details the architecture and components of the CX-Simulator software.
Compares CX-Simulator capabilities with actual PLC operations for effective debugging.
Highlights features that improve program debugging efficiency and user experience.
Lists compatible PLC models, CPU units, and computer requirements for CX-Simulator.
Provides a detailed comparison of CX-Simulator's behavior against actual CS/CJ-series PLCs.
Lists the necessary software prerequisites for installing and operating the CX-Simulator.
Step-by-step guide for installing the CX-Simulator software.
Instructions for removing the CX-Simulator software from the computer.
Explains the methods for starting CX-Simulator and connecting it to CX-Programmer.
Describes the layout and function of the main CX-Simulator windows.
Details how to configure system status, PLC units, UM settings, and clock parameters.
Covers the functions, menus, and operations within the Debug Console for debugging tasks.
Guides users on leveraging CX-Programmer for debugging, highlighting key operational differences.
Explains the various execution modes like Scan Run and Step Run for debugging programs.
Details the process of setting up Step Run, breakpoints, and I/O break conditions for precise debugging.
Covers debugging tasks, including execution time, status monitoring, and individual task execution.
Introduces serial communication capabilities, supported protocols, and hardware.
Provides instructions on setting up serial communication parameters for various units and ports.
Explains methods for connecting to external devices via serial communication.
Demonstrates debugging techniques using message display and serial data files.
Introduces network communication functions, supported protocols, and units.
Guides through setting up network communication parameters for various units.
Explains how to set up network connections and routing tables for FINS communication.
Provides examples for debugging network communications using display messages and local connections.
Explains how to connect the CX-Simulator with other applications for PLC debugging.
Describes connection methods, including coexistence on the same computer and network connections.
Outlines the functions for automating virtual external input creation and data management.
Explains the process of generating, running, and checking results using virtual external inputs.
Details methods like Command Log, Data Trace, Data Replay, and I/O Condition for input generation.
Explains how to run programs using Data Replay Tool, I/O Condition Tool, or a debugging ladder program.
Describes how to verify simulation results using time chart monitoring and Excel graphing.
Describes the fundamental operational flow of the CPU Unit within the CX-Simulator.
Explains cycle time calculation and highlights differences from actual CS/CJ/CP series PLCs.
Details the configuration and usage of I/O memory areas within the CX-Simulator.
Lists common errors encountered during CX-Simulator operation and their solutions.
Provides guidance on resolving connection, network, editing, and cycle time errors.
Introduces the tool for automating the creation of multiple data trace files.
Explains how to set up sampling addresses, files, and options for data trace recording.
To Next Page
General