Panasonic AV-HS6000 - Page 103

– 103 –
Chapter 5 Basic Operations — Storage
f The data saved on memory cards may be lost as a result of misplacing the cards or performing erroneous operations. It is recommended that valuable
data be saved on a computer or other device.
Initializing a memory card
To use a memory card in the unit, make sure to initialize the memory card using the unit. When the unit initializes the memory card, it formats the
memory card (in compliance with the SD standard) and creates a dedicated directory. (All les saved on the memory card will be erased.)
1
Select the <PRJ> button → [PROJECT] → [SD/SSD] tab.
2
Select an item in [Format] in the [SD] column.
f Operate following the conrmation screen.
Saving data on the memory card
Insert the memory card which has been initialized by the unit, into the memory card slot.
Ex) To save a log le
1
Select the <SYS> button → [MAINTENANCE] → [Alarm] tab.
2
Select an item in [Log File] in the [Log] column.
f The [Save] screen is displayed.
[Sort] Sorts the le icon view in ascending or descending order by le number, le name, or date.
[View] Fixed to icon display.
[File Type]
Fixed to le type.
The name of the folder where a log le is saved becomes the le name of the log le.
File names are assigned automatically as follows.
hs001.log to hs100.log
[Cancel] Closes the [Save] screen.
3
Select [OK].
f The le is saved.
@@
NOTE
t For details on the data save destination, refer to “Data folder conguration” (page 102).
t For details on saving project les, refer to “Project management” (page 100).
t For details on saving image les in the video memory (Still, Clip), refer to “Video memory” (page 91).
t For details on saving activation les, refer to “Chromakey Software AV‑SFU60 activation” (page 141).
t For details on saving restore data, refer to “Restoring data” (page 142).
Loading data from the memory card
Insert the memory card on which the data is saved in a specied folder into the memory card slot.
Data stored in other folders will not be recognized by the unit.
Ex) When loading the update le
1
Select the <SYS> button → [MAINTENANCE] → [Status] tab.
2
Select an item in [Update File] in the [Update] column.
f The [Load] screen is displayed.
[Sort] Sorts the le icon view in ascending or descending order by le number, le name, or date.
[View] Fixed to icon display.
[File Type] Fixed to le type.
[Cancel] Closes the [Load] screen.
3
Select a file icon, and select [OK].
f The le is loaded.
@@
NOTE
t For details on the data save destination, refer to “Data folder conguration” (page 102).
t A le name can contain a maximum 32 characters.
t The characters that can be used in a le name are single‑byte alphanumeric characters and single‑byte symbols. Files with a name which contain
other characters are not displayed with the unit. The characters that can be used are as follows.
A to Z, a to z, 0 to 9, ! # $ % & ' ( ) - . @ ^ _ ` { }
t If the name of the le to be loaded consists of more than eight characters, the unit displays a shortened version of the le name.
t For details on loading project les, refer to “Project management” (page 100).
t For details on loading image les from the video memory (Still, Clip), refer to “Video memory” (page 91).
t For details on loading bitmap data of source name and le specications, refer to “Displaying bitmap data” (page 119)
t For details on loading plug-in software, refer to “Plug-in software” (page 148).
t For details on loading activation les, refer to “Chromakey Software AV‑SFU60 activation” (page 141).
t For details on loading backup data, refer to “Creating a backup” (page 141).