– 52 –
Chapter 5 Basic Operations — KEY
[On]
Does not cut key ll with a key signal. The part of key ll not cut out with the key signal is superimposed on the
background image. This item is used when key ll source has been cut with a key signal beforehand using an external
device.
Selecting the source type
Select the mode to link selection of key source signal with key ll selection. The selection status is stored for each source signal.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Setting] tab.
2
Select an item in [Source Type] in the [Key] column.
[Self Key] Uses the source selected in the key ll bus column as the key source signal.
[External Key] Always uses an external key. The source signal for ll is set using [Fill] in the [Key] column.
Selecting the ll type
Select the ll type.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Setting] tab.
2
Select an item in [Fill] in the [Key] column.
[Bus] Uses the bus signal for the key ll signal.
[Matte] Uses the internal ll matte for the key ll signal. The color set in the [Fill Matte] column is used for the ll matte color.
Setting the matte color
Set the ll matte color.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Setting] tab.
2
Adjust the color.
f Set [Hue], [Sat], [Lum], or [Color Palette] in the [Fill Matte] column.
Selecting the key source
Use the KEY bus crosspoint buttons to select key sources for the keys specied using the KEY bus selector buttons.
Setting the link between key ll signal and key source signal
To link the selection of key ll signal and key source signal, select the <CONF> button on the top menu → [SOURCE LINK] → [Key Assign] tab →
[Master/Slave], and set [Fill to Source] or [Source to Fill].
For details, refer to “Setting the key coupling” (page 120).
f [Fill to Source]: When the key ll signal (master) is selected, the key source signal (slave) changes automatically.
f [Source to Fill]: When the key source signal (master) is selected, the key ll signal (slave) changes automatically.
Selecting the key ll signal and the key source signal separately
Use the <BUS SHFT> button to temporarily enable selection of a source different from the link setting using the KEY bus crosspoint buttons.
r When [Fill to Source] is set
Key ll signal: When the KEY bus crosspoint buttons are selected without pressing the <BUS SHFT> button, a key ll signal can be selected. At this
time, the KEY but selector buttons light in Low tally color.
Key source signal: When the KEY bus selector buttons are pressed while the <BUS SHFT> button is held down, the KEY bus selector buttons light in
Preset tally color, and key source different from the link setting can be selected using the KEY bus crosspoint buttons. The changed key source is not
stored as the link setting, and the source returns to the linked source when another key ll source is selected. If the <BUS SHFT> button is pressed and
turned off, select the key ll signal (master) again.
r When [Source to Fill] is set
Key source signal: When the KEY bus crosspoint buttons are selected without pressing the <BUS SHFT> button, a key source signal can be selected.
At this time, the KEY but selector buttons light in Preset tally color.
Key ll signal: When the KEY bus selector buttons are pressed while the <BUS SHFT> button is held down, the KEY bus selector buttons light in Low
tally color. A key ll source different from the link setting can be selected using the KEY bus crosspoint buttons. The changed key ll source is not stored
as the link setting, and the source returns to the linked source when another key source material is selected. If the <BUS SHFT> button is pressed and
turned off, select the key source signal (master) again.
Key transitions
Operating in the transition area
1
Select the transition target.
f Use the <KEY1> to <KEY4> buttons to select a transition target. To select multiple targets, press the <BKGD> button and the <KEY1> to <KEY4>
buttons simultaneously.
To Next Page
Loading...
