Panasonic AV-HS6000 - Page 89

– 89 –
Chapter 5 Basic Operations — Memory
f When [Recall] is selected, playback target items cannot be selected.
[View] Fixed to icon display.
[Page] Switches pages.
[Cancel] Closes the [Recall] screen without recalling the target.
[OK] Closes the [Recall] screen after recalling the target.
Editing macro register memories
Delete a registered register memory or change le names.
1
Select the <MEM> button → [MACRO] → [Register] tab.
2
Select [Misc] in the [Register] column.
f The [Misc] screen is displayed.
[Protect]
Select a le icon and set this item to [On] to protect the relevant le. The protected le is not deleted even when [Delete]
is selected.
[Rename] Select [Rename] after selecting a le icon to change the le name using the on‑screen keyboard.
[Delete] Select [Delete] after selecting a le icon to delete the register memory. It cannot be deleted if [Protect] is set to [On].
[Copy From]
Select the [Copy From] button after selecting the icon of an unregistered register memory, and then specify the register
memory to be the copy source using the on-screen numerical keypad.
Ex) To specify the ninth register memory on the ninth page, input [9.9].
[View] Fixed to icon display.
[Page] Switches pages.
[Close] Closes the [Misc] screen.
Playing back a macro bus on the Control Panel AV‑HS60C1/AV‑HS60C2
The playback trigger of a macro memory can be assigned to the KEY bus cross point buttons.
Assign register memories of the macro memory to the cross point buttons (1 to 24) on the macro bus.
The memories cannot be assigned to the second page to the fourth page of the macro bus.
Within one Control Panel AV-HS60C1/AV-HS60C2, the macro buses of ME1 and ME2 share the assignment.
1
Select the <MEM> button → [MACRO] → [XPT Assign] tab.
f The macro register memories in the right column are assigned to the crosspoints in the left column.
[Panel‑ID] Select the target Control Panel AV-HS60C1/AV-HS60C2 from [MainPanel], [SubPanel1], or [SubPanel2].
[Button Group] Fixed to the view of the rst page of the macro bus.
[Assign] Assigns the macro register memories selected in the right column to the cross point buttons selected in the left column.
[No Assign] Does not assign macro register memories to the cross point buttons selected in the left column.
[Page Select] Switches pages.
@@
NOTE
t Select the <MCRO> button using the cross point area KEY bus selector buttons on the Control Panel AV-HS60C1/AV-HS60C2 to play back the
register memory of the macro memory assigned to the KEY bus cross point buttons.
At this time, the assigned macro name is displayed at the top of the source name display panel.
Playing back using macro attach on the Control Panel AV‑HS60C1/AV‑HS60C2
A trigger to play back each register memory of the macro memory can be assigned to the following buttons.
Crosspoint buttons of the PGM/A-bus/PST/B-bus, and AUX1 to AUX16 buses in ME1/ME2, <AUTO>/<CUT> buttons in ME1/ME2
1
Select the <MEM> button → [MACRO] → [Macro Attach] tab.
f The playback trigger buttons in the right column are assigned to the macro register memories in the left column.
[Enable] When set to [Off], disables all attached operations.
[Insert]
Inserts the copy of the macro same as that of the line selected in the left column in the next line. The number of buttons
to which a macro can be attached is a maximum four per register memory.
[Delete]
Deletes the line copied and inserted using [Insert] selected in the left column. The line cannot be deleted if there is only
one register memory.
[Page] Switches pages.
[Assign] Assigns the playback trigger buttons in the right column to the macro register memories in the left column.
[Panel‑ID] Select the target Control Panel AV-HS60C1/AV-HS60C2 from [MainPanel], [SubPanel1], or [SubPanel2].
[Bus]
Species the bus to be the target of attach setting.
The buttons selected in the right column are disabled when [ME1-CUT], [ME1-AUTO], [ME2-CUT], or [ME2-AUTO] is
selected.
[Timing]
Species the macro timing of the button to which a macro is attached.
[Pre]: Operates the button function after completing the playback of the macro register memory.
[Post]:Plays back the macro register memory after operating the button function.
[Replace]: Plays back the macro register memory without operating the button function.