What causes erratic or unresponsive controls on Raymarine Boating Equipment?
Erratic or unresponsive controls can be caused by a network problem. Check that the controller and thermal camera are correctly connected to the network, either directly or via a Raymarine network switch.
Why is my Raymarine A series Marine Equipment showing the wrong speed?
If you're getting an incorrect speed reading (DST) on your Raymarine Marine Equipment, check that the paddle wheel is clean. Add a speed offset if no speed offset is currently set. Re-calibrate the equipment. If the transducer does not have a speed element, install a transducer with a speed element to enable speed readings.
What to do if my Raymarine A series Marine Equipment product will not boot up (re-boot loop)?
If your Raymarine product is stuck in a reboot loop, the issue might stem from the power supply and connection, so check the solutions for ‘Products does not turn on or keeps turning off’. Another potential cause is software corruption. In that case, try re-flashing the latest software from the Raymarine website. As a last resort on display products, you can perform a ‘Power on Reset’. Be aware that this will erase all your settings, presets, and user data, reverting the unit to factory defaults.
Why is the Bluetooth signal weak or intermittent on my Raymarine Marine Equipment?
If you are experiencing a weak or intermittent Bluetooth signal with your Raymarine Marine Equipment, multiple wireless devices running simultaneously (such as laptops, phones, and other wireless devices) can sometimes cause wireless signal conflicts. Temporarily disable each wireless device in turn until you have identified the device causing the interference.
How do I correct an incorrect target bearing on my Raymarine Boating Equipment radar screen?
If the bearing of a target on the radar screen is incorrect, the radar bearing alignment requires correcting. Check and adjust the radar bearing alignment.
Why is the image upside down on my Raymarine Marine Equipment?
If the image on your Raymarine Marine Equipment is inverted (upside down), ensure that the Ball down setting within the thermal camera system setup menu is set correctly.
Why are the controls erratic or unresponsive on my Raymarine A series?
If you are experiencing erratic or unresponsive controls on your Raymarine Marine Equipment, check that the controller and thermal camera are correctly connected to the network. Verify the status of the Raymarine network switch, and ensure that SeaTalkhs / RayNet cables are free from damage. Make sure that no other controllers are in use at the same time. Check the power and network cabling to the controller and PoE injector (if used). If available, check other controllers to eliminate the possibility of a more fundamental camera fault.
Why do I have no media player control on my Raymarine A series?
If you have no media player control on your Raymarine Marine Equipment, it may be because the media player device is not compatible with the Bluetooth AVRCP protocol (version 2.1 or higher). Check the Bluetooth AVRCP compatibility with the device manufacturer. If the device is not Bluetooth AVRCP compatible then it is not suitable for wireless use with the multifunction display. Also, ensure that “Audio Control” is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Connections > Connections Manager > Audio Control > On).
What to do if Raymarine Boating Equipment radar will not initialize?
If the radar won't initialize due to the Voltage Control Module (VCM) being stuck in “sleep mode”, check the power connection at the VCM. Verify the voltage at the input is 12 / 24 V, and the voltage at the output is 40 V.
How to troubleshoot Raymarine Marine Equipment that won't start?
If your Raymarine Marine Equipment system or part of it does not start up, there could be a power supply problem. Check the relevant fuses and breakers. Also, verify that the power supply cable is in good condition and that all connections are tight and free from corrosion. Finally, ensure that the power source provides the correct voltage and sufficient current.
General| Display Type | LCD |
|---|---|
| Chartplotter | Yes |
| Display Size | 7" |
| Display Resolution | 800 x 480 pixels |
| GPS | Yes |
| Sonar | Yes |
| Cartography | Navionics, C-MAP |
| Radar Support | Yes |
| Waterproof Rating | IPX6 |
Recommends certified installation by an approved installer for enhanced warranty benefits.
Product is an aid to navigation, not a replacement for official charts; accuracy is not warranted.
Information on using microSD cards for data backup, archiving, and chart data.
Guidance on minimizing electromagnetic interference for optimal system performance.
Information on FCC/IC RF exposure limits and antenna placement.
FCC compliance statement and interference statement regarding FCC rules.
Compliance statement regarding Industry Canada license-exempt RSS standards.
Information regarding frequency bands and potential interference with other radio stations.
Lists third-party software licenses applicable to the product.
Importance of ferrites for correct EMC performance and proper installation.
Requirement for suppression ferrites on non-Raymarine cables.
Declares product compliance with R&TTE directive 1999/5/EC.
Guidance on disposing of the product according to the WEEE Directive.
Policy regarding the display of wrongly-illuminated pixels.
Instructions on how to register product ownership online for full warranty benefits.
States equipment is for leisure marine boats, not covered by IMO/SOLAS regulations.
Disclaimer regarding accuracy and continuous product improvement.
Details the scope and applicability of the handbook for Raymarine multifunction displays.
Explains conventions used for icons, menus, applications, and controls within the handbook.
Notes that illustrations may differ slightly from the specific display model.
Details display variants for a Series, c Series, and e Series MFDs, including features.
Lists key features for connecting and controlling a complete marine electronics system.
Details compatibility with various marine electronics devices and protocols.
Lists the essential activities involved in installing the system.
Explains MDS for managing data conflicts and selecting preferred data sources.
Steps to discover the specific model of the multifunction display.
Outlines limitations for general, master/repeater, and specific network connections.
Provides examples of basic and expanded system configurations.
Details data protocols like SeaTalkhs, SeaTalkng, NMEA 2000, SeaTalk, and NMEA 0183.
Explains the function of the data master in a networked system.
Lists the items supplied with a6x and a7x variant MFDs.
Lists the items supplied with a9x and a12x variant MFDs.
Lists the items supplied with e7 / e7D multifunction displays.
Lists items supplied with c Series and e Series (excl. e7/e7D) MFDs.
Lists the necessary tools for product installation.
Guidance on selecting a suitable location considering ventilation, mounting, and interference.
Important considerations for cable types, routing, strain relief, and circuit isolation.
Details available connections on various Raymarine multifunction displays.
Outlines the connections available on the a9x and a12x variant MFDs.
Explains power connection details, including distribution and grounding for a6x/a7x models.
Details the combined power/data cable connection, including distribution and grounding.
Explains how to connect compatible devices using the Network connector.
Describes connecting a remote keypad directly or via a network switch.
Details how to connect Raymarine Non-HD digital radomes and HD/SuperHD radar scanners.
Explains how to connect sonar modules and transducers for the Fishfinder application.
Provides instructions for connecting thermal cameras to the display.
Details how to connect IP cameras to the multifunction display.
Explains how to connect a Sirius XM weather receiver.
Describes connecting a Fusion 700 series marine entertainment system.
Explains connecting internal or external GPS receivers using SeaTalkng or NMEA 0183.
Details connecting the GA150 antenna to improve GNSS reception.
Explains how to connect AIS units using SeaTalkng or NMEA 0183.
Details connecting a fastheading sensor for MARPA functions.
Outlines connecting to a SeaTalkng network for instruments and autopilots.
Explains connecting to NMEA 2000 devices using SeaTalkng.
Describes connecting SeaTalk devices using the optional SeaTalk to SeaTalkng converter.
Details connecting NMEA 0183 devices using the power and data cable.
Explains connecting MFDs to a DSC VHF radio via a SeaTalkng to NMEA 0183 converter.
Describes connecting cameras or video devices to c Series and e Series MFDs.
Details connecting cameras or external displays to e Series MFDs (excluding e7/e7D).
Explains connecting a Bluetooth-compatible media player for wireless control.
Describes connecting a Raymarine remote control wirelessly via Bluetooth.
Information on connecting to Raymarine mobile apps using Wi-Fi.
Instructions for surface and bracket mounting of a Series displays.
Instructions for surface and bracket mounting of c Series and e Series displays.
Procedures for powering the display on, off, and using PowerSave mode.
Details the touchscreen, power, and card reader slot for a Series displays.
Details touchscreen, menu, UniControl, back, power, and card reader for e7/e7D.
Details controls for c/e Series displays, including UniControl and touch icons.
Explains the homescreen as a central access point for applications and data.
Details homescreen for c/e Series, including status symbols and access.
Information on creating, customizing, and moving pages on the homescreen.
Overview of available applications like Chart, Fishfinder, Radar, and Data.
Instructions on how to switch between applications in splitscreen view.
Explains display screen elements: Home, Databar, Status bar, Menus, Context menu.
Details touch operations: cursor movement, touchscreen lock, and control dialogs.
Explains multi-touch gestures like Pinch to Zoom.
Guides through startup wizard, additional settings, display brightness, and minimum safe depth.
Explains how to view GPS status, satellite info, and position fix data.
Steps to enable autopilot control for SeaTalk, SPX, and Evolution autopilots.
How to display engine data and run the Engine identification wizard.
Steps to enable AIS functions by connecting the unit to NMEA Port 1.
How MFDs and instruments share user preference settings across a network.
Instructions for downloading and installing software updates from the Raymarine website.
Information on accessing video tutorials, training courses, FAQs, and technical support forums.
How to check GPS operation using the chart application.
Steps for checking radar operation and bearing alignment.
Guide to selecting sonar channels, transducers, and checking sonar operation.
Instructions for setting up and checking the thermal camera's main functions.
Information on compatible microSD cards, speed ratings, and chart cards.
Instructions for inserting and removing memory or chart cards on a6x and a7x models.
Instructions for inserting and removing memory or chart cards on a9x and a12x models.
Instructions for inserting and removing memory or chart cards on c and e Series models.
How to save waypoints, routes, tracks, and settings to a memory card.
Details data items and settings savable to/restorable from a memory card.
How to take and view screenshots of the display.
Procedures for resetting system settings and data to factory defaults.
How to select the operating language for the system.
Customizing settings like boat type, number of engines, and fuel tanks.
Specifying preferred units of measurement for distance, speed, depth, etc.
Specifying the preferred format for time and date display.
Customizing general display behavior like starting page, key beep, and cursor autohide.
Customizing data displayed in the databar and onscreen databoxes.
Details available data items for display in the Data application.
Overview of menus for configuring display and external devices.
Explains how to view and search PDF documents on the multifunction display.
Details how autopilots can be controlled directly from the MFD.
Steps to enable autopilot control for SeaTalk, SPX, and Evolution autopilots.
Procedures for engaging the autopilot using pilot button, chart menu, or context menu.
How to adjust the locked heading in Auto mode via Pilot Control dialog or Pilot Bar.
Procedures for disengaging the autopilot using power button, shortcuts, pilot button, or chart application.
How to open the Pilot Control dialog from homescreen or chart application.
Explains the Pilot Control dialog for standby, auto, and starting navigation modes.
Describes the Pilot Bar for displaying autopilot status information.
Details the Pilot Set-up page for Evolution autopilots.
Explains vessel settings, drive settings, sail boat settings, and commissioning for Evolution autopilots.
Outlines procedures for commissioning the autopilot system.
Explains the autopilot status symbols indicated in the databar.
Details autopilot alarms and how to silence them.
Explains how alarms alert users to hazards and their severity coding.
Details how to configure alarm behavior and manage alarm activity.
Lists safety and general alarm options and their settings.
Explains using the MOB function to mark position and activate alarm.
Details connecting DSC VHF radio for distress message info and GPS position.
Steps to enable DSC alert display in system settings.
Explains fuel manager for estimating fuel remaining, distance, and time to empty.
Explains AIS for receiving vessel info and displaying targets in chart/radar.
Lists necessary AIS hardware and GPS setup for functionality.
Details AIS target information and menu items accessible via the context menu.
Steps to enable AIS overlay in Chart and Radar applications.
How to display AIS vectors, indicating target prediction and turn direction.
Explains AIS status symbols shown in the databar.
How to disable AIS transmissions while still receiving data.
Describes various symbols used to represent different AIS target types.
How to view detailed AIS target information from chart or radar.
Procedures to view all AIS targets and their detailed information.
How to use Safe Zones and Safety Messages to prevent collisions.
Describes target options like Vector Length and Target History for Chart and Radar.
Details AIS alarms for dangerous or lost targets.
Feature to add friends/contacts to a Buddy List for tracking.
Information on placing, navigating, and managing waypoints.
Explains building, navigating, and managing routes.
Details how to create, review, and edit tracks.
Information on importing and exporting data using a memory card.
Details the storage capacity for waypoints, routes, and tracks.
Details features for route planning and navigation, including charts and waypoints.
Explains world base maps, electronic charts, and LightHouse/Navionics chart compatibility.
Outlines navigation features: Pilot Controls, Goto Cursor, Follow Route, and Build Route.
Explains how to zoom and pan the chart area using various controls.
How to select the cartography type to be used in the Chart application.
Explains how the vessel symbol is displayed and how to locate your vessel.
Details chart orientation modes: Head-Up, North-Up, and Course-Up.
Explains motion modes: Relative Motion, True Motion, and Auto Range.
How to switch between 2D and 3D chart views.
Determines the level of detail displayed on the chart.
Describes chart overlays like AIS, Radar, Aerial, NOWRad, Databoxes, and Chart Grid.
Explains how to enable and disable chart vectors for heading, COG, wind, and tide.
Details how to switch on/off cartographic objects like rocks, nav marks, and routing systems.
How to view detailed information about specific cartographic objects.
Settings for displaying depth soundings and contours.
Access to user data including waypoints, routes, and tracks.
Synchronizing heading, range, and position across multiple chart views.
How to measure distances and bearings using the databar and context menu.
Details the Fishfinder application, sonar module, transducer, and features.
Explains Traditional, CHIRP, DownVisionTM, and SideVisionTM sonar technologies.
Lists Raymarine sonar modules and their specifications.
How to select sonar channels and display multiple channels using custom pages.
Explains SideVision and multiple sonar crosstalk interference and how to reduce it.
How to create, rename, and delete custom sonar channels.
How to interpret the bottom structure and factors influencing the sonar display.
How to define the depth range displayed in the Fishfinder application.
How to define the distance displayed to the left and right of the vessel.
How to pause scrolling or adjust scroll speed for placing waypoints.
How to select display modes like None, Zoom, A-Scope, and Bottom Lock.
How to select Left, Right, or Both views for SideVisionTM channels.
Details options for Target Depth ID, Depth Lines, Range Lines, White Line, Bottom Fill, Color Palette, Scroll Speed, Gain controls, and Databoxes.
How to use Variable Range Markers (VRM) to determine object depth and distance.
How to place waypoints in the Fishfinder application for marking positions.
Accessing features to enhance displayed info: Gain, Color Gain, Contrast, TVG, Noise Filter, Power Mode.
Setting up alarms for fish detection, deep water arrival, and shallow water arrival.
Explains how to fine-tune transducer frequencies for optimal sonar performance.
Details options in Sounder set-up: Ping Rate, Tune Frequency, Interference Rejection.
Lists options for setting up transducers: type, offsets, and speed.
How to reset the sonar unit to its factory default values.
Explains how the Data application enables viewing system and instrument data.
How to scroll through available pages using the touchscreen.
How to select datapages using non-touch controls like the joystick.
How to customize datapages, content, order, and settings.
Details available data items for display in the Data application.
How to display engine data and run the Engine identification wizard.
How to change vessel settings like boat type and number of engines.
How to set the maximum RPM range for the RPM data item.
How to switch the color theme between light and dark.
Specifying preferred units of measurement for distance, speed, depth, etc.
How to reset minimum and maximum readings for data items.
How to reset all datapages to factory defaults.
Explains how RADAR works, its features, and target interpretation.
Details support for up to 2 radar scanners and simultaneous display.
Explains the radar scanner power mode status symbols in the databar.
Provides positional data and menu items for cursor location.
Discusses factors affecting radar image quality: echoes, clutter, interference.
Explains Guard Zone, VRM/EBL, and MARPA for tracking targets and avoiding collisions.
Methods for measuring distances, ranges, and bearings using range rings and cursor.
Details radar orientation (Head-Up, North-Up, Course-Up) and motion modes (Relative, True).
Lists options for Dual Range, Orientation, Motion Mode, Waypoints, and enhancing echoes.
How to use on-screen controls for Gain, Rain, and Sea clutter tuning.
Details presets and functions for improving HD and SuperHD radar picture quality.
Explains gain presets and functions for non-HD digital radomes.
How to view 2 ranges simultaneously in separate windows with SuperHD and HD scanners.
How to set radar scan speed for SuperHD and HD radomes.
Options for configuring radar scanner performance and behavior.
Steps to reset radar settings to defaults.
Details viewing analog and IP camera feeds and associated features.
How to change the displayed video feed using touch or joystick.
How to set Camera application to Quad View for simultaneous display of 4 feeds.
How to set automatic cycling of available feeds at specified time intervals.
How to name camera feeds to distinguish them.
How to adjust image settings like contrast, brightness, and color.
How to manually change the aspect ratio between 4:3 and 16:9.
How to select a location (memory card or internal storage) for recordings.
How to record live IP camera feeds and play them back.
Methods for capturing still images from camera feeds.
How to view photos taken using the Camera application.
Explains controlling and displaying thermal camera images.
Details the thermal camera video feed and status icons.
Lists controls for the thermal camera application.
Procedures for powering up, standby, pan, tilt, and zoom.
How to adjust contrast, brightness, color, and use scene presets.
Menu options for pan and tilt cameras with the new interface.
Details power consumption for high power and high torque modes.
Menu options for pan and tilt cameras with the old interface.
Explains controlling and displaying thermal camera images for fixed mount cameras.
Details the thermal camera video feed and status icons.
Lists controls for the thermal camera application.
Procedures for powering up, standby, and pausing the thermal camera image.
How to adjust contrast, brightness, color, and use scene presets.
Menu options for fixed mount thermal cameras.
Details controlling a connected 700 series Fusion entertainment system.
Describes layout and controls for iPod, USB, DVD, and AM/FM radio sources.
How to browse music on connected iPod or USB devices.
How to set repeat folder or shuffle play order for Fusion link application.
How to adjust volume individually or for all zones simultaneously.
How to select which zone the main screen will control.
How to adjust Bass, Middle, and Treble tone controls.
How to select which Fusion entertainment system the application will control.
Lists menu options for Browse Music, Repeat, Shuffle, Tone Controls, Select Fusion system, Preset, Scan.
Describes overlaying weather graphics on a world map for North America.
Steps required before using the weather application for the first time.
Illustrates main features of the weather application display and weather symbols.
How to move around the weather map and place waypoints.
Provides positional data and options to view weather reports from cursor location.
How to view weather data for specific location, observation station, or city.
How to view various weather reports like Tropical statements and Marine warnings.
How to view animated weather graphics for NOWRad, Wind, Waves, and Pressure.
Lists options available in the weather application menu.
Definitions of common weather terms used in the application.
Details controlling a connected Sirius marine weather/satellite radio receiver.
Information on Raymarine mobile apps for viewing and control via Wi-Fi.
Steps to enable Wi-Fi on the multifunction display.
How to enable mobile apps for video streaming or remote control.
How to encrypt Wi-Fi connections to prevent unauthorized access.
How to manually specify a Wi-Fi channel if experiencing streaming difficulties.
Recommends authorized dealer service and routine equipment checks.
Best practices for cleaning the display screen, case, and sun cover.
Provides possible causes and corrective actions for common marine electronics installation problems.
Addresses problems encountered at power up, like the system not starting.
Details common radar problems and solutions, including no data or incorrect bearing.
Troubleshooting steps for GPS issues like 'No Fix' status.
Addresses warnings and issues encountered when using Autorouting.
Troubleshooting steps for sonar data issues like no data or problematic readings.
Explains SideVision and multiple sonar crosstalk interference and reduction methods.
Addresses common thermal camera problems: no video, erratic controls.
Troubleshooting issues with data shared between connected equipment.
Addresses problems with video inputs, such as no signal message.
Troubleshooting common Wi-Fi connection issues with mobile apps.
Troubleshooting common Bluetooth connection issues.
Addresses touchscreen issues like it not operating as expected.
Procedure to realign the touchscreen for better accuracy.
Covers other common problems like display behaving erratically.
Physical and power specifications for a Series MFDs.
Physical and power specifications for c and e Series MFDs.
Contact info for Raymarine customer support: web, phone, email.
Information on accessing video tutorials, training courses, and FAQs.
Contact and support details for third-party suppliers: Fusion, Navionics, Sirius.
Lists Digital ClearPulse transducers and accessories connectable to sonar variant MFDs.
Lists DownVisionTM transducers and accessories connectable to DownVisionTM variant MFDs.
Details network hardware: HS5 and RJ45 SeaTalkhs network switches.
Describes the two network cable connector types: SeaTalkhs and RayNet.
Lists RayNet to RayNet adapter cables and connectors.
Details SeaTalkhs network and patch cable types.
Lists SeaTalkng cabling components and their purposes.
Lists SeaTalkng cables and accessories for compatible products.
Lists SeaTalk cables and accessories.
Specifies the video cable required for e9/e12 variant MFDs.
Lists spare parts for a Series MFDs.
Lists spare parts for c Series and e Series MFDs.
Details the pinouts for power, data, and video connectors.
Details the pinouts for the network connector.
Details the pinouts for the SeaTalkng connector.
Details the pinouts for the video input/output connector.
Lists supported NMEA 0183 sentences for transmit, receive, and bridging.
Explains how NMEA data bridging allows data repetition between NMEA 2000 and NMEA 0183 devices.
Lists supported NMEA 2000 sentences for NMEA 2000, SeaTalkng, and SeaTalk 2 protocols.
Explains how the display provides monitoring and controls for power circuits and equipment.
Details connecting the multifunction display to an EmpirBus NXT system.
Explains the need for a configuration file and how to load it.
Describes monitoring and controlling vessel systems via the switch panel application.
Details Raymarine's software updates, improvements, and compatibility.
Table showing MFD software versions required to support listed Raymarine hardware.
To Next Page
