Ricoh J001 - Page 248

SM 8-48 J001/J003
Problem Solution
Event
Service Center Call
Response
Probable Cause Operator Action
Content User
ST NRC
Paper jams
between the
trailing edge
sensor and
registration
sensor
(Paper does not
arrive at the
registration
sensor)
Tray 2
During paper feed from Tray 2,
the trailing edge sensor
switched on, but the registration
sensor did not detect the paper,
even though it fed to the
prescribed position. Make sure
that there is no paper inside the
printer.
The paper is folded or caught in the
paper feed path.
(1) If Tray 2 has paper loaded, remove
the paper from the tray.
(2) If the duplex unit is not attached,
open the rear cover of the printer, open
the reverse guide and remove the
paper.
(3) If the duplex unit is attached, detach
it, open the reverse guide, and then
remove the jammed paper.
(4) Open the rear cover of Tray 2,
remove the jammed paper, and then
press [Paper Feed] on the printer
operation panel.
(1) If Tray 2 has paper loaded, remove the paper
from the tray.
(2) If the duplex unit is not attached, open the
rear cover of the printer, open the reverse guide
and remove the paper.
(3) If the duplex unit is attached, detach it, open
the reverse guide, and then remove the jammed
paper.
(4) Open the rear cover of Tray 2, remove the
jammed paper, and then press [Paper Feed] on
the printer operation panel.
X
Paper jams
between the
trailing edge
sensor and
registration
sensor
(Paper does not
arrive at the
registration
sensor)
Duplexing
During duplex printing, or when
the sheet is exiting before
reversal in the duplex unit, the
trailing edge sensor switched
on, but the registration sensor
did not detect the paper, even
though it fed to the prescribed
position.
(The registration sensor detects
the leading edge of the
reversed paper from the duplex
unit.) Make sure there is no
paper in the printer.
- The paper is folded or caught in the
paper feed path.
(1) Remove the duplex unit from the
printer, open the reverse guide.
(2) Remove the paper.
(3) After removing the jam, press the
[Paper Feed] button on the printer.
- Remove the duplex unit from the printer, open
the reverse guide.
- Remove the paper.
- After removing the jam, press the [Paper Feed]
button on the printer.
X
Initial jam
(At initialization
the trailing
edge sensor
switches on.)
- At power on, or during printer
initialization, the trailing edge
sensor goes on. Make sure that
there is no paper inside the
printer.
- Paper remains in the paper path.
- Feed clutch defective.
(1) If the duplex unit is not attached,
open the rear cover of the printer, open
the reverse guide and remove the
paper.
(2) If the duplex unit is attached, open
the rear cover of the duplex unit, open
the reverse guide, remove the jammed
paper, and then press the [Paper Feed]
key on the printer operation panel.
(1) If the duplex unit is not attached, open the
rear cover of the printer, open the reverse guide
and remove the paper.
(2) If the duplex unit is attached, open the rear
cover of the duplex unit, open the reverse guide,
remove the jammed paper, and then press the
[Paper Feed] key on the printer operation panel.
X
Bypass tray jam
(paper rem
ains)
At power on, or during printer
initialization, the bypass set
sensor goes on.
When Tray 1 or Tray 2 is used
for paper feed, the bypass set
sensor goes on. Check the
bypass tray for paper.
Paper remains in the bypass tray. (1)Remove the paper from the bypass
tray.
(2) After removing the jam, press the
[Paper Feed] button on the printer.
Remove the paper from the bypass tray.
- After removing the jam, press the [Paper Feed]
button on the printer.
X
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA