MX-3114N SIMULATION 6 – 31
(*1) Displayed only when EQUITRAC.
(*2) Details of the vendor mode
Details of the vendor mode
Operation 1:
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2:
Auto clear is not made.
Operation 3:
The display is shifted to the initial screen.
26-5
Purpose
Setting
Function (Purpose)
Used to set the count mode of the total
counter and the maintenance counter. (A3/
11x17 size)
Section
Operation/Procedure
1) Select an item to be set with scroll keys.
2) Enter the setting value with 10-key
1 = Count up by 1, 2 = Count up by 2
3) Press [OK] key.
The set value in step 2) is saved.
26-6
Purpose
Setting
Function (Purpose)
Used to set the specifications (paper, fixed
magnification ratio, etc.) of the destination.
Section
Operation/Procedure
1) Select an item to be set with the touch panel.
2) Press [EXECUTE] key.
The selected set content is saved.
26-7
Purpose
Setting
Function (Purpose)
Used to set the machine ID.
Section
Operation/Procedure
1) Enter the machine ID with the 10-key.
Max. 30 digits of numerals and alphabetical characters can be
inputted.
To select a desired character, press the 10-key repeatedly.
Refer to the following list and enter characters.
Touch the "CONFIRM" section every time a character is input-
ted.
To modify an inputted character, delete it with "CLEAR" key
and enter the correct character.
2) Press [SET] key to set the contents entered in procedure 1).
The machine ID can be set also by the Web Page service mode
function.
Conventionally, the machine ID has been set by the Web Page
function. In this mode, this function is made available in the simula-
tion mode.
VENDOR
MODE (*2)
MODE1 Vendor mode 1 MODE
3
MODE2 Vendor mode 2
MODE3 Vendor mode 3
COUNTUP
TIMING
FUSER_IN Mode in which the detection
timing of the paper lead
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
EXIT_
OUT
FUSER_OUT Mode in which the detection
timing of the paper rear
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
EXIT_OUT Mode in which the detection
timing of the paper rear
edge by the paper exit
sensor of the right paper
exit tray or of the after
process unit is used as the
money charging timing.
Completion
of the
specified
quantity.
(Money
remaining)
Insufficient money during
copy job
Completion
of the
specified
quantity.
(No money
remaining)
BW/Color
(no money
remaining)
Color
(Money
remaining)
Condition 1 Condition 2 Condition 3 Condition 4
MODE1 Operation 1 Operation 2 Operation 2 Operation 1
MODE2 Operation 1 Operation 1 Operation 2 Operation 1
MODE3 Operation 1 Operation 3 Operation 2 Operation 3
Item/Display Content Default value
A TOTAL (B/W) Total counter (B/W) 2
B TOTAL (COL) Total counter (Color)
C MAINTE (B/W) Maintenance counter (B/W)
D MAINTE (COL) Maintenance counter (Color)
E DEV (B/W) Developer counter (B/W)
F DEV (COL) Developer counter (Color)
Item/Display Content
Default
value
U.S.A. United States of America
CANADA Canada
INCH Inch series, other destinations
JAPAN Japan
AB_B AB series (B5 detection), other destinations
EUROPE Europe
U.K. United Kingdom
AUS. Australia
AB_A AB series (A5 detection), other destinations
CHINA China
10-key
Number of times of key input
12345678910
1 1---------
2 ABCabc2---
3 DEFdef3---
4 GHIghi4---
5 JKLjkl5---
6 MNOmno6- - -
7PQRSpqrs7-
8 TUVtuv8---
9 WXYZwxyz9-
0 0---------
To Next Page
Loading...
