MX-3114N SIMULATION 6 – 120
67-34
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the density correction in the
printer high density section. (Support for
the high density section tone gap)
Section
Printer
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key. (The set value is saved.)
• When tone gap is generated in the high density section, set items
A and B to "0."
The density in the high density section is decreased, but tone
gap is reduced.
• To increase the density in the high density section further, set
items A and B to "1.
The tone gap may occur in high density part.
Do not change the values of items C, D, E, and F. If these values
are changed, the density in the high density area is changed.
67-36
Purpose
Adjustment/Setup
Function (Purpose)
Used to adjust the density in the low den-
sity section.
Section
Printer
Operation/Procedure
1) Enter the adjustment value using the 10-key.
2) Press [OK] key.
When the adjustment value is increased, the low density images
are strongly reduced. When the adjustment value is decreased, the
low density are images are weakly reproduced.
When tone gap is generated in the low density section (highlight
section), changing this adjustment value may improve the trouble.
67-41
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the threshold for judging the
selected color printing or the black color
printing in the black and white mode.
Section
Printer
Operation/Procedure
1) Select a set value with the scroll key.
2) Enter the set value with 10-key.
3) Press [OK] key.
67-42
Purpose
Adjustment
Function (Purpose)
Used to adjust the gradation by increasing /
decreasing the selected color componet
amount or the black color component
amount in the black and white mode.
Section
Printer
Operation/Procedure
1) Select Mode1 or Mode2.
2) Select an item to be set.
0 Enable
1Disable
Item/Display Content
Setting
range
Default
value
ACMY
(0: ENABLE
1: DISABLE)
0 CMY engine highest
density correction
mode: Enable
0 - 1 0
1 CMY engine highest
density correction
mode: Disable
BK
(0: ENABLE
1: DISABLE)
0 K engine highest
density correction
mode: Enable
0 - 1 1
1 K engine highest
density correction
mode: Disable
C CYAN MAX
TARGET
Scanner target value for
CYAN maximum density
correction
0 - 999 500
DMAGENTA
MAX TARGET
Scanner target value for
MAGENTA maximum density
correction
0 - 999 500
E YELLOW MAX
TARGET
Scanner target value for
YELLOW maximum density
correction
0 - 999 500
F BLACK MAX
TARGET
Scanner target value for
BLACK maximum density
correction
0 - 999 500
Item/Display Content
Setting
range
Default
value
A A PATCH INPUT A patch input value 0 - 13 1
Item/Display Content
Setting
range
Default
value
A C1 Mode1 : Threshold of Saturation 0 - 255 5
B
V1 Mode1 : Threshold of Brightness
0 - 255 0
C C2 Mode2 : Threshold of Saturation 0 - 255 5
D V2 Mode2 : Threshold of Brightness 0 - 255 0
Mode
Item/Display Content
Default
value
MODE
1
Black
(Achromatic
color)
F1 Black : Light F2
F2 Black : Normal
F3 Black : Dark
COLOR
(Selected
color)
G1 Selected color : Light G2
G2 Selected color : Normal
G3 Selected color : Dark
MODE
2
Black
(Achromatic
color)
F1 Black : Light F2
F2 Black : Normal
F3 Black : Dark
COLOR
(Selected
color)
G1 Selected color : Light G2
G2 Selected color : Normal
G3 Selected color : Dark
To Next Page
Loading...
