MX-3114N SIMULATION 6 – 121
67-43
Purpose
Adjustment
Function (Purpose)
2 Color mode balance adjustment
Section
Printer
Operation/Procedure
1) Select an adjustment item with the scroll key.
2) Enter the set value with 10-keys.
3) Press [OK] key.
67-45
Purpose
Adjustment/Setup
Function (Purpose)
Used to adjust the printer image filter and
trapping.
Section
Printer
Operation/Procedure
1) Select an adjustment item with the scroll key.
2) Enter the set value.
3) Press [OK] key.
67-52
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the default of the gamma of the
printer screen.
Section
Printer
Operation/Procedure
1) Select a target default setting mode with the touch panel.
Press [ALL] key to select all the modes.
2) Press [EXECUTE] key and press [YES] key.
When the printer screen gamma was changed by SIM 67-33,
SIM67-54, it is reset to the default.
PCL/PS printer
GDI printer
Item/Display Content
Color
Setting
range
Default value
CMY
ARED
R output
color
CMY 0 - 255 0 235 224
BGREEN
G output
color
CMY 0 - 255 180 0 241
CBLUE
B output
color
CMY 0 - 255 235 159 0
DCYAN
C output
color
CMY 0 - 255 182 0 25
EMAGENTA
M output
color
CMY 0 - 255 0 217 0
F YELLOW
Y output
color
CMY 0 - 255 0 0 234
Item/Display Content
Setting
range
Default
value
NOTE
A SHARPNESS:
COLOR PRINT
Color print 0 - 4 2 The greater
the set value
is, the
stronger the
filer
enhancement
is. The smaller
the set value
is, the
stronger the
filter
smoothness
is.
(0: Soft High,
1: Soft Low, 2:
Center, 3:
Sharp Low, 4:
Sharp High)
B SHARPNESS:
B/W PRINT
Monochrome
print
0 - 4 2
C TRAPPING:
CMY (PCL &
DIRECTPRINT)
CMY
(PCL, Direct
Print)
0 - 5 3 The greater
the set value
is, the
stronger the
trapping is.
(0: OFF, (Low)
1 < 2 < 3 < 4 <
5)
(The target is
vector images.
There is no
effect for the
raster
images.)
However, the
sharpness
also varies.
D TRAPPING: K
(PCL &
DIRECTPRINT)
K
(PCL, Direct
Print)
0 - 5 3
E TRAPPING:
CMY (PS)
CMY (PS) 0 - 5 3
F TRAPPING: K
(PS)
K (PS) 0 - 5 0
G TRAPPING:
CMY (XPS)
CMY (XPS) 0 - 5 0
H TRAPPING: K
(XPS)
K (XPS) 0 - 5 0
Item/Display Content
Screen HEAVYPAPER Heavy paper screen
Printer heavy paper automatic density
correction amount
600DPI_1BIT SCREEN1 (600dpi 1bit Photo)
SCREEN2 (600dpi 1bit Graphics)
B/W SCREEN7 (600dpi 1bit Graphics)
SCREEN8 (600dpi 1bit Graphics)
SCREEN9 (600dpi 1bit Graphics)
Printer B/W toner save automatic density
correction amount
GLOSSPAPER SCREEN10 (Glossy paper screen)
Display Content
600DPI 1BIT
600dpi 1bit Low (Photo)
600dpi 1bit High (Graphics)
Gloss 600dpi 1bit
B/W B/W 600dpi 1bit
Item/Display Content
Setting
range
Default
value
NOTE
To Next Page
Loading...
