MX-3114N ADJUSTMENTS AND SETTINGS 5 – 47
3) Enter the adjustment value with 10-key and press [OK] key.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
4) Make a copy and check the adjustment result.
Switch the adjustment simulation mode and the normal copy
mode alternately, and adjust and check the adjustment result.
Repeat switching the adjustment simulation mode and the nor-
mal copy mode and changing the adjustment value and check-
ing the copy until a satisfactory result is obtained.
10-D (2)
Monochrome copy density adjustment
(for each monochrome copy mode)
(separately for the low-density area and the
high-density area)
(No need to adjust normally)
The density is adjusted in each copy mode individually.
This adjustment must be performed in the following cases:
* When there is necessity to change the copy density of the low
density and high density part at each copy density individually.
* When there is necessity to change the density gradient of the
copy by each the copy mode individually.
* When there is necessity to change all copy density by each the
copy mode individually.
* When there is request from the user.
1) Enter the SIM 46-2 mode.
2) Select the copy mode to be adjusted with the scroll key.
3) Enter the adjustment value with 10-key and press [OK] key.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
4) Make a copy and check the adjustment result.
Switch the adjustment simulation mode and the normal copy
mode alternately, and adjust and check the adjustment result.
Repeat switching the adjustment simulation mode and the nor-
mal copy mode and changing the adjustment value and check-
ing the copy until a satisfactory result is obtained.
10-D (3)
Color copy color balance, gamma
adjustment (for each color copy mode)
(No need to adjust normally)
This adjustment is used to execute the color balance adjustment
for each density level in each color copy mode.
This adjustment must be performed in the following cases:
* When there is necessity to change the color balance and gamma
by each the copy mode individually.
* When there is request from the user.
OK
㪈㪇㪄㫂㪼㫐
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17%:>&23<@
$˖
˷˹
˖$872
$˖
˖$872
%˖
˖7(;7
&˖
˖7(;735,17('3+272
'˖
˖35,17('3+272
)˖
˖7(;73+272
(˖
˖3+272*5$3+
*˖
˖0$3
+˖
˖7(;7&23<72&23<
,˖
˖7(;735,17('3+272&23<72&23<
-˖
˖35,17('3+272&23<72&23<
.˖
˖/,*+7
/˖
2.
+,*+/2:
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17%:>&23<@
$˖
˷˹
˖$872
$˖
˖$872
%˖
˖7(;7
&˖
˖7(;735,17('3+272
'˖
˖35,17('3+272
)˖
˖7(;73+272
(˖
˖3+272*5$3+
*˖
˖0$3
+˖
˖7(;7&23<72&23<
,˖
˖7(;735,17('3+272&23<72&23<
-˖
˖35,17('3+272&23<72&23<
.˖
˖/,*+7
/˖
2.
+,*+/2:
Display/Item Content
Setting
range
Default
A AUTO1 Auto 1 LOW 1 - 99 50
HIGH 1 - 99 50
B AUTO2 Auto 2 LOW 1 - 99 50
HIGH 1 - 99 50
C TEXT Text LOW 1 - 99 50
HIGH 1 - 99 50
D TEXT/PRINTED
PHOTO
Text/Printed
Photo
LOW 1 - 99 50
HIGH 1 - 99 50
E TEXT/PHOTO Text/Photograph LOW 1 - 99 50
HIGH 1 - 99 50
F PRINTED PHOTO Printed Photo LOW 1 - 99 50
HIGH 1 - 99 50
G PHOTOGRAPH Photograph LOW 1 - 99 50
HIGH 1 - 99 50
H MAP Map LOW 1 - 99 50
HIGH 1 - 99 50
ITEXT
(COPY TO COPY)
Text (Copy
document)
LOW 1 - 99 50
HIGH 1 - 99 50
J TEXT/PRINTED
PHOTO
(COPY TO COPY)
Text/Printed
Photo (Copy
document)
LOW 1 - 99 50
HIGH 1 - 99 50
K PRINTED PHOTO
(COPY TO COPY)
Printed Photo
(Copy document)
LOW 1 - 99 50
HIGH 1 - 99 50
L LIGHT Light document LOW 1 - 99 50
HIGH 1 - 99 50
To Next Page
Loading...
Need help?
General
