Table of contents
5.30 Remote Setting Function (P.61) ....................................................................................................... 111
5.31 Zero Current Detection (P.62 and P.63) ............................................................................................ 113
5.32 Retry Function (P.65, P.67, P.68, P.69) ............................................................................................. 114
5.33 Brake Selection (P.71) ..................................................................................................................... 116
5.34 Carrier Frequency (P.72).................................................................................................................. 116
5.35 Stop or Reset Function Selection (P.75) ........................................................................................... 118
5.36 Parameters Write Protection (P.77) .................................................................................................. 118
5.37 Forward/Reverse Rotation Prevention Selection (P.78) .................................................................... 119
5.38 Operation Mode Selection (P.79) ..................................................................................................... 119
5.39 Multi-function Terminal Function Selection (P.80~P.84, P.86, P.126, P.550) ....................................... 120
5.40 Multi-function Terminal Input Negative/Positive Logic(P.87) .............................................................. 127
5.41 Multi-Function Output Terminal Positive/Negative Logic (P.88) ......................................................... 128
5.42 Slip Compensation Coefficient (P.89) ............................................................................................... 128
5.43 The Inverter Model (P.90) ................................................................................................................ 129
5.44 Frequency Jump (P.91~P.96) ........................................................................................................... 129
5.45 Programmed Operation Mode (P.100~P.108, P.111~P.118, P.121~P.123, P.131~P.138) .................... 130
5.46 Operation Panel Monitoring Selection (P.110) .................................................................................. 132
5.47 The selection of positive and reverse rotation dead time (P.119) ....................................................... 133
5.48 Zero-Speed Function (P.151~P.152) ................................................................................................ 134
5.49 Over Torque Detection (P.155~P.156, P.260) .................................................................................... 134
5.50 External Terminals Filter Adjusting Function (P.157) ......................................................................... 135
5.51 External Terminal Power Enable Function (P.158) ............................................................................ 136
5.52 Energy-Saving Control Function (P.159) .......................................................................................... 136
5.53 Multi-Function Display (P.161) ......................................................................................................... 137
5.54 PID Parameters 1 (P.170~P.183, P.223~P.225, P.241) ...................................................................... 138
5.55 4-5 Terminal Disconnection Handling Function (P.184) ..................................................................... 144
5.56 The Proportion Linkage Function and The Auxiliary Frequency Function (P.185, P.240).................... 144
5.57 SF-GT Types Selection (P.186) ........................................................................................................ 146
5.58 Firmware version and expansion board message (P.124, P.188) ...................................................... 146
5.59 Factory Setting Function (P.189) ...................................................................................................... 146
5.60 2-5 Terminal Input Signal (P.139, P.192~P.195, P.510~P.513) ........................................................... 147
5.61 4-5 Terminal Input Signal (P.196~P.199, P.505) ................................................................................ 153
5.62 1-5 Terminal Input Signal (P.506，P.514~P.521) .............................................................................. 154
5.63 Backlash Compensation Function Selection and Acceleration and Deceleration Interrupt Waiting
Function(P.229~P.233) V/F .................................................................................................................. 155
5.64 Triangular Wave Function (P.234~P.239).......................................................................................... 156
5.65 DC Brake Function before Starting (P.242~P.244) ............................................................................ 157
5.66 Options for Stopping the Cooling Fan (P.245) ................................................................................... 158
5.67 Modulation Coefficient (P.246) ......................................................................................................... 159
5.68 Commercial Power Supply Frequency Operation Function (P.247~P.250) ........................................ 159
5.69 Maintenance Alarm Function (P.261) ............................................................................................... 162
5.70 Regeneration and Avoidance Function (P.267~P.272) ...................................................................... 163
5.71 Input Phase Failure Protection (P.281) ............................................................................................ 165
5.72 Vibration Inhibition Factor (P.285 and P.286) .................................................................................... 165
5.73 Short Circuit Protection Function (P.287) .......................................................................................... 166
To Next Page
Loading...
Need help?
General
