Name: SICK MLG-2 WebChecker
Brand: SICK
Rating: 5 (1 reviews)

To Next Page

To Previous Page

11.1.2 “Device” area

Table 42: “Device” area

Designation Description

Type Shows the MLG-2 type code.

Part no. Shows the MLG-2's part number.

Serial no. Shows the serial number of the MLG-2.

Device ID Shows the device ID (IO-Link).

Hardware version Shows the hardware version.

Firmware version Shows the firmware version.

Response time Shows the current response time in ms.

Scaling Shows the current resolution in mm/mA. Only with MLG-2 variants

wit

h analog outputs.

Cycle time Shows the current cycle time in ms. .

Application-specific day Enter application-specific day.

Factory setting: *******

CONFIGURATION WITH SOPAS 11

8025190/2020-01-13 | SICK O P E R A T I N G I N S T R U C T I O N S | MLG-2 WebChecker

Subject to change without notice

Default Chapter3
- Table of Contents3
1 About this Document7
- Purpose of this Document7
- Scope7
- Target Group7
- Information Depth7
- Symbols Used7
- Abbreviations Used8
2 Safety Information9
- Requirements for the Qualification of Personnel9
- Intended Use9
- General Safety Notes10
3 Product Description11
- Type Labels of the MLG-2 Webchecker11
- Type Code13
- Structure and Function16
  - Device Components16
  - Measurement Principle17
- Definitions18
- Scan Time19
- Operating Reserve19
- Minimum Object Attenuation20
- Display and Operating Elements20
  - Webchecker with Fieldbus Interface20
  - Fieldbus Module21
- Inputs23
  - Switching Inputs on the Receiver23
  - Test Input on the Sender23
- Application Examples23
  - Application Examples for the MLG-2 Webchecker23
4 Planning25
- Planning Mounting Distance between Sender and Receiver25
- Identifying Optimal Object Position26
- Determining Measurement Accuracy for Actual Object Position27
- Required Minimum Distances for an Object28
- Required Minimum Distances for Several Objects29
- Minimum and Maximum Object Width29
- Edge Measurement and Edge Designation30
- Functions: Calculation of Width and Center Positions32
5 Mounting33
- Scope of Delivery33
  - Webchecker with Fieldbus Interface33
- Recommended Mounting Arrangements33
- Mounting Procedure35
6 Electrical Installation42
- Fieldbus Module Connections42
- Sender Connections44
- T-Connector for MLG-2 Webchecker Connection45
7 Commissioning47
- Putting the MLG-2 Webchecker into Operation47
- Aligning Sender and Receiver47
- Performing Sensor Teach-In48
- Performing Material Teach-In49
- Calling up Teach-In Quality and Process Quality49
8 Operating MLG-2 Via Control Panel51
- Activating and Deactivating Pushbutton Lock51
- Alignment and Teach-In51
- Performing Sensor Teach-In53
- Performing Material Teach-In53
- Reset to Factory Settings54
9 Commissioning Via SOPAS55
- Preparation55
  - Installing the Software55
  - Device Selection55
- Setting up MLG-2 Webchecker (Installation Assistant)55
- Setting up Edge Measurement61
- Parameterizing Functions: Calculation of Width and Center Positions61
- Other Configurations62
10 The MLG-2 Webchecker in the Fieldbus Network63
- The MLG-2 in PROFINET63
- The MLG-2 on the Ethernet/Ip™ Network68
- Object Library80
11 Configuration with SOPAS86
- Start" Page86
12 Servicing105
13 Troubleshooting106
- Response to Faults106
- SICK Support106
- LED Displays and Error Indicators106
14 Decommissioning110
- Disposal110
- Returns110
15 Technical Data111
- Data Sheet111
- Webchecker Fieldbus Module Data Sheet113
- Diagrams114
- Dimensional Drawings119
  - Webchecker Dimensional Drawing119
  - Dimensional Drawings for the MLG-2 Fieldbus Module121
16 Accessories123
17 Annex126
- Compliance with EU Directive126
18 List of Figures127
19 List of Tables129

Brand	SICK
Model	MLG-2 WebChecker
Category	Measuring Instruments
Language	English

SICK MLG-2 WebChecker User Manual

Table of Contents

Questions and Answers:

SICK MLG-2 WebChecker Specifications

Related product manuals