Siemens FS720 - Technical Terms and Abbreviations

178 pages

To Next Page

To Previous Page

About this doc

ument

Technical terms and abbreviations

12 | 178

Building Technologies

A6V10210416_j_en_

Fire Safety

2018

1.3 Technical terms and abbreviations

Term Explanation

AI Alarm indicator

BDV Base data variant

C-NET Addressed detector line

ES Product version

MCL Maintenance and commissioning link

'MCP' Abbreviation for 'Manual call point'

You will find details of further technical terms and abbreviations in the 'Glossary'

chapter.

See also

2 Applicable documents [➙ 11]

Main Page

Default Chapter3
- Table of Contents3
1 About this Document9
- Applicable Documents11
- Download Center11
- Technical Terms and Abbreviations12
- Revision History13
2 Safety17
- Safety Instructions17
- Safety Regulations for the Method of Operation18
- Standards and Directives Complied with20
- Release Notes21
3 Mounting / Installation22
- Installing and Checking the Detector Line22
- Mount and Install 'Station23
4 Connectivity and Communication with 'Station24
- Setting Windows Firewall24
  - Windows XP24
  - Windows 7 / Windows 8 / Windows 1025
- Network Parameters26
- Connecting the PC to the Station27
- Disconnecting the PC from the Station27
- Loading Data to the 'Station28
- Initializing 'Station28
- Loading Configuration from the PC to the Station30
- Loading Configuration from the Station to the PC32
- Creating a Backup of the 'Site' Configuration32
5 Commissioning Overview34
- Commissioning Variants34
- Definition of Terms35
- Standard Gateway36
- Brief Instructions on Operating the 'Station37
- License37
6 Commissioning Standalone 'Station' Without PC38
- Configuring the Power Supply39
- Entering Customer Texts Using the Person Machine Interface39
- Setting Detector Parameter Sets40
7 B1 - Commissioning Standalone 'Station' with PC, Without Pre-Configuration41
8 B2 - Commissioning Standalone 'Station' with PC, with Pre-Configuration42
9 Commissioning Networked 'Stations43
10 Adding a 'Station' to an Existing 'Site44
11 Merging Two 'Sites45
- Adding 'Site' B to 'Site' a46
- Connecting 'Sites' Physically to One Another46
12 Changing and Expanding the Fdnet/C-NET Detector Line47
- Extending the Detector Line to Include Additional Devices47
  - Mount and Wire New Devices47
  - Configure a New Device48
- Replacing Stationary Devices of the same Type48
- Permanently Removing Stationary Devices49
- Removing or Replacing Non-Stationary Devices49
- Replacing 'Manual Call Point' of the same Type55
- Convert Two Stubs into a Loop56
- Connecting a Sub-Stub to a Loop57
13 Calibrating an Fdnet/C-NET Detector Line58
- Automatic Line Calibration59
- Manual Line Calibration60
- Calibration Report61
- Troubleshooting66
14 Commissioning a Control Panel with Integrated Extinguishing70
- Preparing the Control Panel with Integrated Extinguishing for Commissioning71
- Calibrating Monitored Outputs72
- CE Marking73
15 Detailed Commissioning Steps74
- Preparing 'Station' for Commissioning74
- Preparing 'Station' for Commissioning -Without BDV Installation75
- Auto-Configuring 'Station75
- Auto-Configuring the Detector Line76
- Loading Automatically Created Configuration to the PC77
- Adapting Configuration77
- Converting a Standalone Station to a Networked Station78
- Switch off79
  - Safety During Switch-Off79
  - Switching off the Detector Line79
  - Switch off Zone79
- Switching on79
  - Switch on Detector Line79
  - Switch on Zone80
- Restarting the Detector Line80
- Freezing Outputs81
- Enabling Frozen Outputs81
- Read in Devices on Detector Line82
- Detaching the Device82
- Delete the Device on Person Machine Interface83
- Remove the Elements83
- Testing Detectors83
  - Activate the Detector84
  - Testing Logged Test Activations84
- Switching on Test Mode84
- Switch on Normal Operation85
- Rectify Localization Errors86
- Checking 'Site' Function86
- Carrying out Final Commissioning Work86
16 Commissioning Ethernet Switch (MM) FN2008-A187
- Install Primary Setup Tool88
- Assign IP Address88
- Configuring FN2008-A1 Using Internet Browser89
17 Commissioning Ethernet Switch (Modular) FN2012-A190
- Standalone FN2012-A190
  - Specifying a Pre-Configured IP Address90
- FN2012-A1 Integrated into Station92
- FN2012-A1 Web Interface93
- Restarting and Resetting the FN2012-A197
18 Commissioning Security Module (Firewall) FN2009-A198
- Installing Security Configuration Tool99
- Selecting Type and Entering MAC Address100
- Entering Network Settings101
- Creating IP Service Definitions104
- Creating Firewall Rules106
19 Commissioning the Fire Brigade Periphery Module FCI2001-D1108
20 Commissioning of I/O Card (Remote Transmission) FCI2007-A1 and I/O Card (Horn/Monitored) FCI2009-A1109
21 Commissioning External Printer110
22 Updating the Firmware113
- Preparation and Security113
- Station: Updating the FW of the Main CPU and Additional Cpus114
- Station: Updating the FW of the Additional Cpus Only125
- Update Only the BDV127
  - Standalone Station and SAFEDLINK Station127
  - Router Station and Ethernet Station128
- Converting the Configuration128
- Testing the Firmware Version of the Additional Cpus129
- Creating Diagnosis Report130
- Updating the FW of the Peripheral Devices130
- Updating the FW of Ethernet Switch (Modular) FN2012-A1142
  - Standalone FN2012-A1142
  - FN2012-A1 Integrated into Station145
23 Maintenance146
- General146
- Testing146
- Testing and Measuring Instruments147
- Preparatory Work147
- Test System Data148
- Testing the 'Station149
- Check the Power Supply150
- Testing the Printer150
- Calibrating Lines151
- Checking 'Site' Function151
- Intervals for Testing the System Function152
- Carrying out Final Maintenance Work153
24 Repair154
- Disconnect the Station from the Power Supply154
- Spare Parts155
- Fault Messages on the Person Machine Interface156
- Fault Indicators on Components157
- Communication Problems in Networked Systems157
- Correcting Swapped Devices158
- Correcting an Invalid Topology159
- Error Message 'Too Many Devices159
- Restart 'Station160
- Resetting a Short-Circuit161
- Restoring Factory Setting on the 'Station163
- Fiber-Optic Network Module FN2006 / FN2007 Troubleshooting Steps165
- Glossary170
- Index174

Siemens FS720 - Technical Terms and Abbreviations

Table of Contents

Other manuals for Siemens FS720

Related product manuals