Siemens FS720 - Page 69

To Next Page

To Previous Page

Calibrating an FDnet/C

NET detector line

Troubleshooting

69 |

178

Building Technologies

A6V10210416_j_en_

Fire Safety

2018

See also

2 Manual line calibration [➙ 60]

Main Page

Default Chapter3
- Table of Contents3
1 About this Document9
- Applicable Documents11
- Download Center11
- Technical Terms and Abbreviations12
- Revision History13
2 Safety17
- Safety Instructions17
- Safety Regulations for the Method of Operation18
- Standards and Directives Complied with20
- Release Notes21
3 Mounting / Installation22
- Installing and Checking the Detector Line22
- Mount and Install 'Station23
4 Connectivity and Communication with 'Station24
- Setting Windows Firewall24
  - Windows XP24
  - Windows 7 / Windows 8 / Windows 1025
- Network Parameters26
- Connecting the PC to the Station27
- Disconnecting the PC from the Station27
- Loading Data to the 'Station28
- Initializing 'Station28
- Loading Configuration from the PC to the Station30
- Loading Configuration from the Station to the PC32
- Creating a Backup of the 'Site' Configuration32
5 Commissioning Overview34
- Commissioning Variants34
- Definition of Terms35
- Standard Gateway36
- Brief Instructions on Operating the 'Station37
- License37
6 Commissioning Standalone 'Station' Without PC38
- Configuring the Power Supply39
- Entering Customer Texts Using the Person Machine Interface39
- Setting Detector Parameter Sets40
7 B1 - Commissioning Standalone 'Station' with PC, Without Pre-Configuration41
8 B2 - Commissioning Standalone 'Station' with PC, with Pre-Configuration42
9 Commissioning Networked 'Stations43
10 Adding a 'Station' to an Existing 'Site44
11 Merging Two 'Sites45
- Adding 'Site' B to 'Site' a46
- Connecting 'Sites' Physically to One Another46
12 Changing and Expanding the Fdnet/C-NET Detector Line47
- Extending the Detector Line to Include Additional Devices47
  - Mount and Wire New Devices47
  - Configure a New Device48
- Replacing Stationary Devices of the same Type48
- Permanently Removing Stationary Devices49
- Removing or Replacing Non-Stationary Devices49
- Replacing 'Manual Call Point' of the same Type55
- Convert Two Stubs into a Loop56
- Connecting a Sub-Stub to a Loop57
13 Calibrating an Fdnet/C-NET Detector Line58
- Automatic Line Calibration59
- Manual Line Calibration60
- Calibration Report61
- Troubleshooting66
14 Commissioning a Control Panel with Integrated Extinguishing70
- Preparing the Control Panel with Integrated Extinguishing for Commissioning71
- Calibrating Monitored Outputs72
- CE Marking73
15 Detailed Commissioning Steps74
- Preparing 'Station' for Commissioning74
- Preparing 'Station' for Commissioning -Without BDV Installation75
- Auto-Configuring 'Station75
- Auto-Configuring the Detector Line76
- Loading Automatically Created Configuration to the PC77
- Adapting Configuration77
- Converting a Standalone Station to a Networked Station78
- Switch off79
  - Safety During Switch-Off79
  - Switching off the Detector Line79
  - Switch off Zone79
- Switching on79
  - Switch on Detector Line79
  - Switch on Zone80
- Restarting the Detector Line80
- Freezing Outputs81
- Enabling Frozen Outputs81
- Read in Devices on Detector Line82
- Detaching the Device82
- Delete the Device on Person Machine Interface83
- Remove the Elements83
- Testing Detectors83
  - Activate the Detector84
  - Testing Logged Test Activations84
- Switching on Test Mode84
- Switch on Normal Operation85
- Rectify Localization Errors86
- Checking 'Site' Function86
- Carrying out Final Commissioning Work86
16 Commissioning Ethernet Switch (MM) FN2008-A187
- Install Primary Setup Tool88
- Assign IP Address88
- Configuring FN2008-A1 Using Internet Browser89
17 Commissioning Ethernet Switch (Modular) FN2012-A190
- Standalone FN2012-A190
  - Specifying a Pre-Configured IP Address90
- FN2012-A1 Integrated into Station92
- FN2012-A1 Web Interface93
- Restarting and Resetting the FN2012-A197
18 Commissioning Security Module (Firewall) FN2009-A198
- Installing Security Configuration Tool99
- Selecting Type and Entering MAC Address100
- Entering Network Settings101
- Creating IP Service Definitions104
- Creating Firewall Rules106
19 Commissioning the Fire Brigade Periphery Module FCI2001-D1108
20 Commissioning of I/O Card (Remote Transmission) FCI2007-A1 and I/O Card (Horn/Monitored) FCI2009-A1109
21 Commissioning External Printer110
22 Updating the Firmware113
- Preparation and Security113
- Station: Updating the FW of the Main CPU and Additional Cpus114
- Station: Updating the FW of the Additional Cpus Only125
- Update Only the BDV127
  - Standalone Station and SAFEDLINK Station127
  - Router Station and Ethernet Station128
- Converting the Configuration128
- Testing the Firmware Version of the Additional Cpus129
- Creating Diagnosis Report130
- Updating the FW of the Peripheral Devices130
- Updating the FW of Ethernet Switch (Modular) FN2012-A1142
  - Standalone FN2012-A1142
  - FN2012-A1 Integrated into Station145
23 Maintenance146
- General146
- Testing146
- Testing and Measuring Instruments147
- Preparatory Work147
- Test System Data148
- Testing the 'Station149
- Check the Power Supply150
- Testing the Printer150
- Calibrating Lines151
- Checking 'Site' Function151
- Intervals for Testing the System Function152
- Carrying out Final Maintenance Work153
24 Repair154
- Disconnect the Station from the Power Supply154
- Spare Parts155
- Fault Messages on the Person Machine Interface156
- Fault Indicators on Components157
- Communication Problems in Networked Systems157
- Correcting Swapped Devices158
- Correcting an Invalid Topology159
- Error Message 'Too Many Devices159
- Restart 'Station160
- Resetting a Short-Circuit161
- Restoring Factory Setting on the 'Station163
- Fiber-Optic Network Module FN2006 / FN2007 Troubleshooting Steps165
- Glossary170
- Index174

Siemens FS720 - Page 69

Table of Contents

Other manuals for Siemens FS720

Related product manuals