Siemens Milltronics BW500/L - Page 10

Table of contents
BW500 and BW500/L
8 Operating Instructions, 12/2016, A5E33482052-AD
12.8 Batch Control (P560 – P568) ............................................................................................... 176
12.8.1 P560 Batch Mode Control .................................................................................................... 176
12.8.2 P564 Batch Setpoint ............................................................................................................ 177
12.8.3 P566 Batch Pre-Warn .......................................................................................................... 177
12.8.4 P567 Batch Pre-Warn Setpoint ............................................................................................ 177
12.8.5 P568 Batch Pre-Act ............................................................................................................. 177
12.8.6 P569 Manual Batch Pre-Act Amount ................................................................................... 178
12.8.7 P598 Span Adjust Percentage ............................................................................................. 178
12.9 Totalization (P619 - P648) ................................................................................................... 178
12.9.1 P619 Totaling Dropout ......................................................................................................... 178
12.9.2 P620 Display Zero Dropout .................................................................................................. 178
12.9.3 P621 mA Zero Dropout ........................................................................................................ 179
12.9.4 P631 Totalizer Resolution .................................................................................................... 179
12.9.5 P634 Communication Totalizer Resolution .......................................................................... 180
12.9.6 P635 Verification Totalizer ................................................................................................... 180
12.9.7 P638 External Totalizer Resolution...................................................................................... 181
12.9.8 P643 External Contact Closure ............................................................................................ 182
12.9.9 P647 Totalizer Display ......................................................................................................... 182
12.9.10 P648 Totalizer Reset, Internal ............................................................................................. 182
12.9.11 P680 Test Load: Weight (Options)....................................................................................... 183
12.9.12 P681 Total Mass of Test Weights ........................................................................................ 183
12.9.13 P682 Average Idler Spacing ................................................................................................ 183
12.9.14 P690 Speed Constant Entry ................................................................................................
183
12.
9.15 P691 Drive Pulley Diameter ................................................................................................. 184
12.9.16 P692 Pulses Per Sensor Revolution .................................................................................... 184
12.10 ECal Parameters (P693 – P698) .......................................................................................... 184
12.10.1 P693 Load Cell Capacity Units ............................................................................................ 184
12.10.2 P694 ECal Load Cell Capacity ............................................................................................. 184
12.10.3 P695 ECal Load Cell Sensitivity .......................................................................................... 185
12.10.4 P696 ECal Load Cell Excitation ........................................................................................... 185
12.10.5 P697 ECal Idler Spacing ...................................................................................................... 185
12.10.6 P698 ECal Conveyor Inclination .......................................................................................... 185
12.10.7 P699 ECal mV Span ............................................................................................................ 186
12.10.8 P735 Back Light ................................................................................................................... 186
12.10.9 P739 Time Zone................................................................................................................... 186
12.11 Communication (P740 - P799) ............................................................................................. 187
12.11.1 P742 Word Order Parameter ............................................................................................... 187
12.11.2 P750 – P769 SmartLinx Module Specific Parameters ......................................................... 187
12.11.3 P770 – P789 Local Port Parameters ................................................................................... 187
12.12 SmartLinx Hardware Testing ............................................................................................... 187
12.12.1 P790 Hardware Error ........................................................................................................... 188
12.12.2 P791 Hardware Error Code ................................................................................................. 188
12.12.3 P792 Hardware Error Count ................................................................................................ 188
12.12.4 P794 SmartLinx Module Type .............................................................................................. 188
12.12.5 P795 SmartLinx Protocol .....................................................................................................
189
12.
12.6 P799 Communications Control ............................................................................................ 189
12.13 Test and Diagnostic (P900 - P951) ......................................................................................
189
12.
13.1 P900 Software Revision ....................................................................................................... 189
12.13.2 P901 Memory Test ............................................................................................................... 189