Siemens SIMOCODE pro - Page 186

Tables, data records
3.3 Tables, PROFIBUS data records
SIMOCODE pro - Communication
186 Function Manual, 11/2018, A5E40508495002A/RS-AC/003
Byte.Bit
Designation (PRM group)
Type
Range
Unit
Default
Note
Information
7.5 Monitoring external fault 6 Bit 0, 1 0 1 = Only motor
ON
BU2(+)
7.6 Reserved Bit 0
7.7
Reserved
Bit
0
8.0 Calculation module 2 - Operating
mode
Bit 0, 1 0 0 = Word
1 = D-word
BU2(+)
8.1
Reserved
Bit
0
8.2 DM-F - Safe tripping function Bit 0, 1 0 0 = No
1 = Yes
DM-F
8.3 DM-F - reset safety-related tripping Bit 0, 1 0 0 = Manual,
1 = Auto
DM-F
8.4
Time stamping active
Bit
0, 1
0
BU2(+)
8.5
Reserved
Bit
0
8.6
Reserved
Bit
0
8.7
Reserved
Bit
0
9.0
DM-FL - Configuration 1
Bit
0, 1
0
Configurable
parameters
comparable with
the module
configuration
DM-FL
9.1
DM-FL - Configuration 2
Bit
0, 1
0
DM-FL
9.2
DM-FL - Configuration 3
Bit
0, 1
0
DM-FL
9.3
DM-FL - Configuration 4
Bit
0, 1
0
DM-FL
9.4
DM-FL - Configuration 5
Bit
0, 1
0
DM-FL
9.5
DM-FL - Configuration 6
Bit
0, 1
0
DM-FL
9.6
DM-FL - Configuration 7
Bit
0, 1
0
DM-FL
9.7 DM-FL - Configuration 8 Bit 0, 1 0 DM-FL
10.0
Bit[2] - Parameters (21)
10.0 3UF50 basic type Bit[2] 0, 1, 2 0 BU2(+)
10.2
Reserved
Bit[2]
0
10.4 UVO timebase Bit[2] 0, 1, 2 0 0 = 100 ms,
1 = 1 s,
2 = 10 s
BU2(+)
10.6 UVO operating mode Bit[2] 0, 1 0 0 = Deactivated,
1 = Activated
BU2(+)
11.0
Trip monitoring U<
Bit[2]
0, 1, 2
1
0 = ON (always)
1 = on+
(always, not TPF)
2 = RUN (motor
ON, not TPF)
UM(+)
11.2 Warning monitoring U< Bit[2] 0, 1, 2 1 UM(+)
11.4
Reserved
Bit[2]
0
11.6
Reserved
Bit[2]
0
12.0
Trip monitoring 0/4-20 mA>
Bit[2]
0, 1, 2, 3
0
0 = ON (always)
1 = ON +
(always, not TPF)
2 = RUN (motor
ON, not TPF)
AM1
12.2
Warning monitoring 0/4-20 mA>
Bit[2]
0, 1, 2, 3
0
AM1
12.4
Trip monitoring 0/4-20 mA<
Bit[2]
0, 1, 2, 3
0
AM1
12.6
Warning monitoring 0/4-20 mA<
Bit[2]
0, 1, 2, 3
0
AM1
13.0
Monitoring limit 1
Bit[2]
0, 1, 2, 3
0
BU2(+)