Siemens SIMODRIVE 611 universal - 6.1 Operating mode, speed;torque setpoint (P0700 = 1)

6
6-330
 Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
6.6.4 Torque/power reduction via terminal 24.x/20.x 6-536. . . . . . . . . . . . . . . . . . . . . . .
6.6.5 Application example master/slave 6-539. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.7 Analog outputs 6-541. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.8 Angular incremental encoder interface (X461, X462) 6-555. . . . . . . . . . . . . . . . .
6.8.1 Angular incremental encoder interface as output (P0890 = 1) 6-557. . . . . . . . . .
6.8.2 Angular incremental encoder interface as input (P0890 = 2, from SW 3.3) 6-562
6.8.3 Electronic handwheel (from SW 8.1) 6-566. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.9 Motor holding brake 6-569. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.10 Parameter set changeover 6-575. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.11 Motor changeover for induction motors (from SW 2.4) 6-579. . . . . . . . . . . . . . . .
6.11.1 General information on motor changeover 6-579. . . . . . . . . . . . . . . . . . . . . . . . . .
6.11.2 Changeover, max. 4 motors each with 1 data set (P1013 = 1) 6-585. . . . . . . . .
6.11.3 Changeover, 1 motor with max. 4 data sets (P1013 = 2) 6-587. . . . . . . . . . . . . .
6.11.4 Changeover, max. 2 motors each with 2 data sets (P1013 = 3) 6-588. . . . . . . .
6.11.5 Parameters for motor changeover 6-591. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.12 Travel to fixed endstop (positioning mode) (from SW 3.3) 6-593. . . . . . . . . . . . .
6.13 Teach–in (from SW 4.1) 6-600. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.14 Dynamic servo control (DSC, from SW 4.1) 6-602. . . . . . . . . . . . . . . . . . . . . . . . .
6.15 Spindle positioning (from SW 5.1) 6-604. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.16 Rotor position synchronization/rotor position identification 6-614. . . . . . . . . . . . .
6 Description of the Functions
01.99
04.05