E
E-921
Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
Optimization
Closed-loop current and speed control-
lers, 6-336
Position controller, 6-378
Optional module
PROFIBUS-DP, 1-25, 1-32, 1-41, 2-80
TERMINALS, 1-25, 1-32, 1-40, 2-78
Output signal, analog, 6-542
Output signal, digital
Actual motor (from SW 2.4), 6-518
Angular incremental encoder handwheel
active (from SW 8.1), 6-525
Angular incremental encoder handwheel
evaluation, bit 0 (from SW 8.1), 6-525
Angular incremental encoder handwheel
evaluation, bit 1 (from SW 8.1), 6-525
Axis moves backwards, 6-521
Axis moves forwards, 6-521
Cam switching signal 1, 6-523
Cam switching signal 2, 6-523
Comparison value reached/comparison
value not reached, 6-515
Control requested/no control possible,
6-515
Control via PROFIBUS (from SW 3.1),
6-513
DC link monitoring V–DC link greater
than V–x, 6-510
Direct output 1 via the traversing block,
6-524
Direct output 2 via the traversing block,
6-524
Drive stationary/drive moving, 6-517
External block change (from SW 7.1),
6-519
Fault present/no fault present, 6-510
First speed setpoint filter inactive, 6-518
Fixed end stop reached (from SW 3.3),
6-520
Fixed endstop clamping torque reached
(from SW 3.3), 6-521
Function generator active (from SW 6.1),
6-518
Heatsink temperature pre-warning, 6-506
In synchronism (from SW 3.3), 6-521
Inactive, 6-504
Integrator inhibit, speed controller, 6-508
M less than M–x, 6-505
MDI active (from SW 7.1), 6-524
Minus software limit switch actuated,
6-522
Motor being changed over (from SW
3.3), 6-518
Motor overtemperature pre-warning,
6-506
Motor selected (from SW 2.4), 6-508
n–act less than n–min, 6-504
n–act less than n–x, 6-505
n–set is equal to n–act, 6-509
No following error/following error, 6-514
No OFF 2 present/OFF 2 present, 6-513
No OFF 3 present/OFF 3 present, 6-514
Open holding brake, 6-511
Open–loop torque controlled mode,
6-507
Parameter set, 6-508
Parking axis selected, 6-511
Plus software limit switch actuated, 6-522
Power module current not limited (from
SW 3.1), 6-512
Power–on inhibit/no power–on inhibit,
6-514
Pulses enabled (from SW 3.1), 6-512
Ramp–function gen. inactive, 6-518
Ramp–up completed, 6-504
Ready or no fault, 6-511
Ready to be powered–up/not ready to be
powered–up, 6-513
Reference point set/no reference point
set, 6-516
Reference position reached/outside refe-
rence position, 6-516
Request passive referencing (from SW
5.1), 6-520
Setpoint acknowledge, 6-517
Setpoint static, 6-521
Slave sign–of–life (from SW 3.1), 6-519
Spindle position reached (from SW 5.1),
6-514
Spindle positioning on (from SW 5.1),
6-510
Status, block selection, 6-513
Status, controller enable, 6-510
Status, fixed speed setpoint (from SW
3.1), 6-509
Suppress fault 608 active (from SW 3.1),
6-519
Teach–in executed (from SW 4.1), 6-517
Tracking mode active, 6-520
Traverse to fixed end stop active (from
SW 3.3), 6-519
Variable signaling function, 6-507
Velocity limiting active, 6-524
Warning present/no warning present,
6-510
04.05
To Next Page
Loading...
