Siemens SIPROTEC 7SJ62 Instruction Manual

viii 7SJ62 Instruction Manual
C53000-G1140-C121-1
6.6 Sensitive Ground Fault Detection (64, 50Ns, 67Ns)..........................................................6-73
6.6.1 Description of Sensitive Ground Fault Detection............................................................... 6-73
6.6.1.1 Voltage Element ................................................................................................................6-73
6.6.1.2 Current Elements...............................................................................................................6-74
6.6.1.3 Determination of Direction................................................................................................. 6-74
6.6.1.4 Location of Ground Connections ....................................................................................... 6-78
6.6.2 Programming Settings .......................................................................................................6-79
6.6.2.1 Settings for Sensitive Ground Fault Detection...................................................................6-83
6.6.2.2 Information List for Sensitive Ground Fault Detection .......................................................6-85
6.7 Negative Sequence Protection (46)...................................................................................6-86
6.7.1 Description of Negative Sequence Protection ................................................................... 6-86
6.7.1.1 Determination of Unbalanced Load ................................................................................... 6-86
6.7.1.2 Definite Time Elements (46-1, 46-2)..................................................................................6-86
6.7.1.3 Inverse Time Element (46-TOC)........................................................................................ 6-87
6.7.2 Programming Settings .......................................................................................................6-89
6.7.2.1 Settings for Negative Sequence (Phase Balance) Current Protection ..............................6-91
6.7.2.2 Information List for Negative Sequence Current Protection .............................................. 6-93
6.8 Motor Starting Protection (48)............................................................................................ 6-94
6.8.1 Description of Motor Starting Protection............................................................................6-94
6.8.2 Programming Settings .......................................................................................................6-96
6.8.2.1 Settings for Motor Starting Time Monitoring......................................................................6-97
6.8.2.2 Information List for Motor Starting Time Monitoring...........................................................6-98
6.9 Thermal Overload Protection (49) .....................................................................................6-99
6.9.1 Description of Thermal Overload Protection......................................................................6-99
6.9.2 Programming Settings .....................................................................................................6-101
6.9.2.1 Settings for Thermal Overload Protection........................................................................6-104
6.9.2.2 Information List for Thermal Overload Protection............................................................6-105
6.10 Start Inhibit for Motors (66/68).........................................................................................6-106
6.10.1 Description of Start Inhibit for Motors ..............................................................................6-106
6.10.2 Programming Settings .....................................................................................................6-108
6.10.2.1 Settings for Start Inhibit of Motors ...................................................................................6-109
6.10.2.2 Information List for Start Inhibit of Motors........................................................................6-110
6.11 Voltage Protection (27, 59)..............................................................................................6-111
6.11.1 Description of Voltage Protection ....................................................................................6-111
6.11.1.1 Measurement Principle....................................................................................................6-111
6.11.1.2 Overvoltage Protection (59).............................................................................................6-111
6.11.1.3 Undervoltage Protection (27)...........................................................................................6-112
6.11.2 Programming Settings .....................................................................................................6-115
6.11.2.1 Overvoltage Protection ....................................................................................................6-116
6.11.2.2 Settings for Overvoltage Protection................................................................................6-116
6.11.2.3 Information List for Overvoltage Protection ..................................................................... 6-116
6.11.2.4 Undervoltage Protection ..................................................................................................6-117
6.11.2.5 Settings for Undervoltage Protection...............................................................................6-118
6.11.2.6 Information List for Undervoltage Protection ...................................................................6-119
www . ElectricalPartManuals . com

Siemens SIPROTEC 7SJ62 Specifications

General

Brand	Siemens
Model	SIPROTEC 7SJ62
Category	Relays
Language	English