115
Interface Processor D Series
Interface Processor D Series
Applicable Models
PFV-HD50A HD Digital Video Interface Unit
Supplied Accessories
Operation manual (1)
Installation manual (1)
Optional Software
HZPF-9003 576 Input Option Software
HZPF-9005 Aspect/Color Processing Option
Software
HZPF-9006 1035/30P Option Software
HZPF-9001 720P Input Option Software
HZPF-9002 480 Input Option Software
Optional Peripherals
HKDV-900 HD Digital Video Controller
Specifications
Inputs/outputs
Digital signal inputs:
SD IN 1,2 connector (BNC type) (2),
525/625 component digital serial signal
with embedded audio conforming to
SMPTE259M, 270 Mb/s, 0.8 Vp-p, 75 Ω,
unbalanced
HD IN connector (BNC type) (1), HD
digital serial signal with embedded
audio conforming SMPTE291M/292M/
299M, BTA S-004B/005B/006B, 1.4835
Gb/s or 1.485 Gb/s, 75 Ω, unbalanced
Cable length:
200 m max. (SD)
(With Fujikura 5C2V or equivalent
coaxial cable)
100 m max. (HD)
(with Fujikura 5C-FB or equivalent
coaxial cable)
Input return loss:
15 dB or more (5 MHz to 270 MHz)
Reference input:
REF IN connector (BNC type) (1), 1125
tri-level sync signal conforming to
SMPTE274M or 525/625 Black Burst
signal
Digital signal outputs:
SD OUT1, 2 connector (BNC type) (2),
component digital serial signal with
embedded audio conforming to
SMPTE259M, 270 Mb/s, 0.8 Vp-p
610%, 75 Ω, unbalanced
HD OUT1, 2 connector (BNC type) (2),
HD digital serial signal with embedded
audio conforming SMPTE291M/292M/
299M, BTA S-004B/005B/006B, 0.8 Vp-p
610%, 75 Ω, unbalanced
Output return loss:
15 dB or more (5 MHz to 270 MHz)
Jitter:
Alignment jitter, 740 ps (SD), 135 ps or
less (HD)
Rise/fall time:
1.5 ns or less (SD), 270 ps or less (HD)
Loop-through output:
Loop-through output connector (BNC
type) (1)
Remote control:
D-sub 9-pin, female (2)
General
Power requirements:
+5 V DC: 5.0 A, -5 VDC: 3.0 A
(Supplied from PFV-HD Series Interface
Unit)
Operating temperature:
5 to 40 °C (41 to 104 °F)
Storage temperature:
-20 to 60 °C (-4 to 140 °F)
Operating humidity:
10 to 90% (no condensation)
Dimensions
Board (H x W):
194 x 310 mm
(7 3/4 x 12 1/4 inches)
Connector panel (H x D x W):
218 x 98 x 25 mm
(8 5/8 x 3 7/8 x 1 inches)
Mass
Board:
Approx. 700 g (1 lb 3 oz)
Connector panel:
Approx. 600 g (1 lb 5 oz)
The HKPF-9000 multi-format converter converts 1080/24P
HDTV format signals to a variety of HD/SD formats. It
provides optional functions that convert SDTV or 720P to
HDTV 1080, frame rate and aspect ratio. For details, see
the Format Conversion Table. The HKPF-9000 is
configured as two boards for installation in the PFV-HD
Series Interface Units in any combination with other HKPF
Series boards.
Features
*Built-in colorimetry conversion between 601/240M/709
*Down/up-conversion to/from 720/60P (with optional
HZPF-9001 software) *Up-converts SDTV signal to 1080i
(with optional HZPF-9002/9003 software) *Line
conversion between 1035 and 1080 active lines (with
optional HZPF-9006 software) *Built-in image enhancer
and output gamma corrector *Selectable aspect ratio
conversion (Edge Crop/Squeeze/Letter Box) *Embedded
audio and time code are locked to the output signal after
video format conversion *Variable image trimming and
aspect ratio manipulation, background color selection
(with optional HZPF-9005 software) — Remote Control
function enables video gain, image enhancer, etc., to be
remotely controlled from an optional HKDV-900 HD digital
video controller
The HKPF Series function boards install in the PFV-HD Series Interface Units.
HKPF-9000 Multi-format converter
Rear Panel Rear Panel
*SGC_0099-0116 02.3.16 5:05 PM Page 115
To Next Page
Loading...
