How to fix smudged print on Tally Dascom Printer?
If your Tally Dascom printer is producing smudged prints, consider these solutions: 1. Check the ribbon for damage (e.g., frayed edges) and replace it if necessary. 2. The printhead gap may be too small. Increase the gap. 3. If your printer has AGA = ON, enter a correction value >0 (correction value 0 to +10).
How to resolve paper jam in Tally Dascom 2810 Printer?
To resolve a paper jam in your Tally Dascom printer: 1. Open the top cover and remove the jammed paper by tearing it off at the tear off edge. 2. Press the key to transport the paper backwards. 3. Support the paper return feed by cautiously pulling the paper in the correct direction. Before replacing the fanfold paper, ensure you: * Insert the paper straight. * Close the tractors after inserting the paper. * Adjust the tractors so the paper is positioned straight but without tension. * Adjust the printhead gap to the paper thickness (if AGA=Off). * Set the parameter Head-up to On. * Clean upper friction.
What to do if Tally Dascom Printer prints undefined characters?
If your Tally Dascom printer is printing undefined characters, here are some steps to troubleshoot the issue: 1. First, check that the interface plug is correctly connected to both the computer and the printer. 2. Next, verify that the proper emulation and the correct character set (country, CG table or character set) is selected in the Setup menu. 3. Check the length of the interface cable. 4. Set CX-bid in the advanced menu to Off. 5. Ensure the printer is properly adapted to the computer (configured). Check the parameter set in the Setup menu under Settings for interfaces (I/O), and if necessary correct it.
Why is the print too pale on my Tally Dascom 2810?
If the print from your Tally Dascom printer is too pale: 1. Check if the ribbon is used up or the ribbon cassette is not correctly fitted. 2. Verify that the printhead to platen gap is correctly set. 3. For printers with AGA = ON: Enter a correction value
What to do if Tally Dascom 2810 does not feed paper?
If your Tally Dascom printer is not feeding paper: 1. Check that the display shows the correct paperway, if necessary select the correct paperway with the key Park. If you wish to use optional paper types, make sure they are correctly installed. 2. Make sure that the paper guide is correctly adjusted at the side. When having torn off the fanfold paper the fanfold paper moves to the park position. If necessary, drive the remaining paper manually to the park position with the ? key.
What to do if Tally Dascom 2810 does not print with the internal Ethernet interface (ETH-INT)?
If your Tally Dascom printer is not printing via the internal Ethernet interface: 1. Check that a proper interface cable is used: Cat.5e, 100 MHz. 2. Verify that the connected switch or hub is set like the printers interface e.g. Switch Printer 100 MHz, Full duplex 100/Full or Autosense Autosensing. 3. In the printout of the menu settings the actual connection link status is reported. 4. The LED next to the RJ45 connector are indicating the link status of the ETH-INT. green off: no link green flash: link orange off: half duplex orange on: full duplex.
Crucial instructions for safe printer operation and maintenance.
Identification of printer components and their functions.
Steps for unpacking, placing, connecting, and powering on the printer.
Procedure for inserting the printer ribbon cassette.
Guides for installing drivers on Windows and other OS.
Understanding the control panel, display, and modes of operation.
Adjusting print head gap, tear position, and character settings.
Accessing and navigating the printer's menu for advanced settings.
Configuring serial, Ethernet, and other interface parameters.
Selecting character sets, emulations, and fonts for printing.
Enabling and configuring various barcode types for printing.
Accessing test functions and advanced printer configurations.
Configuring paper motion sensors, width detection, and margins.
Using PJL commands and control sequences for printer management.
Diagnosing and resolving issues with printing and paper feed.
Procedures for routine maintenance and cleaning.
Detailed performance data, dimensions, and environmental conditions.
List of optional hardware, interface modules, and consumables.
General| Type | Dot Matrix Printer |
|---|---|
| Interface | Parallel, Serial, USB |
| Number of Pins | 24 |
| Print Technology | Impact Dot Matrix |
| Print Resolution | 360 x 360 dpi |
| Noise Level | 55 dB |
| Emulation | IBM Proprinter, Epson LQ |
| Paper Handling | Tractor feed |
| Paper Path | Front, Rear |
| Printing Method | Matrix |
To Next Page
