Index
Index- 20
CSA7000B Series & TDS7000B Series Instruments User Manual
runt, C--7
runt setup, C--8
serial pattern, C--7
serial pattern setup, C--8
setup/hold, C--7
setup/hold setup, C--8
timeout, C-- 7
timeout setup, C-- 8
transition, C--7
transition setup, C-- 8
width, C--7
width setup, C--8
window, C--7
window setup, C--8
Trigger point, defined, 3--36
Trigger when
A Trigger, 3--97
A Trigger control window, 3--96, 3--99
transition is <, A Trigger control window, 3--91
transition time >, A Trigger control window, 3 --91
Trigger, delayed, how to set up, 3--110
Trigger, glitch, how to set up, 3--83
Trigger, runt, how to set up, 3--85–3--118
Trigger, slew rate, how to set up, 3--89–3--118
Trigger, timeout, how to set up, 3--94
Trigger, width, how to set up, 3--87–3--118
Triggering
advanced, 3--65
advanced triggering, 3--77
comm triggering, 3--65, 3--117
define inputs, 3--98
define logic, 3--98
define the clock source and edge, 3--100
define the da ta source, 3--100
delayed trigger system, 3--68
edge, 3--65
glitch trigger, 3--78
horizontal position, 3--67
logic qualify, 3--102
logic trigger definitions, 3--80
overview of, 3--63
pattern trigger, 3--79
posttrigger, 3--64
pretrigger, 3--64
runt trigger, 3--78
select glitch triggering, 3-- 83
select runt triggering, 3--85
select setup/hold Triggering, 3--99
select the polarity, 3--85, 3--87
select the polarity and width, 3--83
select the source, 3--83, 3--85, 3--87, 3--89, 3--94
select timeout triggering, 3-- 94
select transition triggering, 3--89
select width triggering, 3--87
sequential trigger reset, 3--109
sequential triggering, 3--103
serial pattern tri ggering, 3 --65, 3--117
set the data and clock levels, 3--100
set the level, 3--84, 3--88, 3--95
set the setup and hold times, 3--101
set the thresholds, 3--86
set the timer, 3 --94
set the transition time, 3 --90
set thresholds, 3--98
set to trigger if width, 3--84
set to trigger when, 3--85, 3--88, 3--91, 3--94
set trigger when, 3--99
Setting mode and holdoff, 3 --93
setup/hold trigger, 3--80
slope and level, 3--67
state trigger, 3--80
the trigger event, 3--64
timeout trigger, 3--79
to check trigger status, 3--72
to define a time qualified pattern trigger, 3--97
to define new trigger level presets, 3--76
to define pattern inputs, 3--96, 3--103
to define the logic, 3--96, 3--103
to force a trigger, 3--76
to logic qualify a trigger, 3--102
to reset sequential triggers, 3--111, 3--112, 3--113
to select a preset trigger level, 3--75
to select the trigger mode, 3--71
to select the trigger slope, 3--69
to select the trigger source, 3--70
to select the trigger type, 3--69
to set holdoff, 3--74
to set level, 3--69
to set mode and holdoff, 3--84, 3--87, 3--88, 3--91,
3--95, 3--97, 3--99, 3--101
to set the trigger coupling, 3--71
to set thresholds, 3--96, 3--103
to set to 50%, 3--70
to set trigger when, 3--96
to set up B Triggering, 3--115
to single trigger, 3--77
to trigger based on transition time, 3 --89
to trigger on A (Main) only, 3--109
to trigger on a glitch, 3--83
to trigger on a pattern, 3--96
to trigger on a runt pulse, 3--85
to trigger on a state, 3--98
to trigger on B After Time, 3--110
to trigger on B Events, 3--110
to trigger on setup/hold time violations, 3-- 99
transition trigger, 3--79
To Next Page
Loading...
