ADCMT 7352A User Manual

7352 Series Digital Multimeter Operation Manual
Alphabetical Index
I-2
How to Replace Protection Fuses ........... 8-3
How to Use Dual Display ....................... 4-26
How to Use Dual Display by Remote
Operation ................................................ 4-27
HOW TO USE THE INTERFACE ........ 6-1
[ I ]
If a Fault Occurs ..................................... 2-1
Input Cable .............................................. 3-5
Inspection on Delivery ............................ 3-1
Installation Environment ......................... 3-3
Interface Selection .................................. 6-1
Interface Specifications ........................... 7-16
INTRODUCTION .................................. 1-1
[L]
Loading the Setting Parameters .............. 5-39
[M]
MAINTENANCE ................................... 8-1
MAX/MIN Calculation ........................... 5-35
Measurement Function and Range
Structure .................................................. 5-9
Measurement Function Keys .................. 4-2
Measurement Functions .......................... 4-8, 5-8
Measurement Range and Auto-Range .... 5-9
Measurement Range Selection Keys ...... 4-3
Memory Clear ......................................... 5-40
Memory Recall ....................................... 5-40
Memory Store ......................................... 5-40
Menu ....................................................... 5-1
Menu List ................................................ 5-4
MENU OPERATION AND FUNCTION
DESCRIPTION ...................................... 5-1
MENU/ENTER Key ............................... 4-3
[N]
Note when Turning on the Power ........... 2-2
Notes Regarding Repair, Replacement,
and Periodic Calibration ......................... 8-16
NULL Calculation .................................. 5-25
[O]
Operating Environment ........................... 3-3
Output Data Format ................................ 6-13
Overview ................................................. 6-2, 6-5,
6-9
[P]
Panel Description .................................... 4-1
Power Fuse .............................................. 2-1
Power Requirements ............................... 3-8
Power Switch .......................................... 4-2
PRECAUTIONS ..................................... 2-1
Precautions in Use of GPIB .................... 6-3
Preparing for Calibration ........................ 8-5
Product Disposal and Recycle ................ 8-13
Product Overview ................................... 1-2
Protecting Against Electrostatic
Discharge ................................................ 3-4
[Q]
QUICK START ...................................... 4-1
[R]
Rear Panel Description ........................... 4-6
Removing the Case ................................. 2-1
Replacing a Power Fuse .......................... 8-1
Replacing a Protection Fuse ................... 8-2
Replacing Fuses ...................................... 8-1
Replacing Parts with Limited Life .......... 8-12
Right or Left Display Section Selection
Key .......................................................... 4-4
RS-232 Output Data Format ................... 6-8
RS-232 Setting ........................................ 6-6
RS-232[EIA-232] (7352A) ..................... 6-5
[S]
Sample Programs .................................... 6-52
Sample Programs (GPIB commands used
in ADC CORPORATION) ..................... 6-52
Sample Programs (RS-232) .................... 6-60
Sample Programs (SCPI commands
for GPIB) ................................................ 6-56
Sample Programs (USB) ......................... 6-62
Sampling Count Setting .......................... 5-17
Sampling Operation ................................ 5-13
Sampling Selection Keys ........................ 4-3
Saving and Loading the Measurement
Condition Settings ................................... 5-39
Saving the Setting Parameters ................ 5-39
Scaling Calculation ................................. 5-28
SCPI Command Reference ..................... 6-31
Selecting the Command Language ......... 6-11
Self-Test .................................................. 8-22
Setting the Measurement Range ............. 4-22
Setting Up the USB Port ......................... 6-9
SETUP .................................................... 3-1
SHIFT/EXIT/LOCAL Key ..................... 4-4
Single Measurement ............................... 5-14
Smoothing Calculation ........................... 5-26
SPECIFICATIONS ................................. 7-1

ADCMT 7352A Specifications

General

Brand	ADCMT
Model	7352A
Category	Multimeter
Language	English