AGCO LELY RPC 130 F User Manual

2.3.9 Feed Channel Floor .............................................. 42
2.3.10 Bale Chamber .................................................. 42
2.3.11 Tying Unit ..................................................... 42
2.3.12 Tailgate ....................................................... 42
2.3.13 Pivoted Roller ...................................................42
2.3.14 Bale Transfer ................................................... 43
2.3.15
Wrapper ...................................................... 43
2.3.16 Wrapping Table ................................................. 44
2.3.17 Wrapping Ring .................................................. 44
2.3.18 Stretch Unit .................................................... 44
2.3.19
Film Knife ..................................................... 44
2.3.20
Cameras
...................................................... 44
2.3.21 Bale Tipper (optional) ............................................. 45
2.3.22 Bale Mat (optional) ............................................... 45
2.4 Controllers ......................................................... 46
2.4.1 E-Link Pro ..................................................... 46
2.4.2 Keyboard ...................................................... 47
2.5 E-Link Pro Software ................................................. 49
2.5.1
Home Page E-Link Pro and ISOBUS .................................. 50
2.5.2
Bale Adjustments Page ............................................53
2.5.3
Field Statistics .................................................. 57
2.5.4
Tasks Page .....................................................57
2.5.5 Advanced Menu ................................................. 58
3 Operation ................................................................ 65
3.1 First Use ........................................................... 67
3.1.1 Calculate the Maximum Permitted Vertical Load on the Coupling Point ......... 67
3.1.2 Calculate the Maximum Permitted Horizontal Load on the Coupling Point ....... 67
3.1.3 Adjust the Height of the Drawbar .................................... 67
3.1.4 Adjust the Power Take-O (PTO) Shaft .................................68
3.1.5 To Prepare Before You Connect the Power Supply ........................ 70
3.1.6 Connect the Hydraulics ............................................71
3.1.7 Adjustment for Load Sensing System ................................. 71
3.1.8 Prepare the Chain Lubrication System ................................. 72
3.1.9 Adjust the Net Roll Holder ......................................... 72
3.1.10 Adjust the Pre-stretch Rate ......................................... 73
3.1.11 Adjust the Film Roll Holder for Size ................................... 74
3.1.12 Spare Film Rolls ................................................. 75
3.1.13 Seal Plate (RPC 160 V) ............................................ 75
3.1.14 Setup the E-Link Pro Display ........................................ 76
3.1.15 Calibration of Wrapper Parts ........................................ 78
3.1.16 Install the Bale Mat (optional) ....................................... 78
3.1.17 Install the Bale Tipper (optional) ......................................78
3.2 Connect the Machine to the Tractor .................................. 80
3.3 Transport Position and Driving ....................................... 82
3.3.1 Transport Position of the Bale Mat (optional) ............................ 85
3.3.2 Transport Position of the Bale Tipper (optional) ........................... 85
3.3.3 Apply or Release the Parking Brake ................................... 86
3.3.4 Place or Remove the Wheel Chocks .................................. 87
3.3.5 Drain the Air Container of the Pneumatic Brake System .................... 87
3.4 Prepare the Machine to Bale ......................................... 88
3.4.1 Adjust The Height of the Pick-up ..................................... 88
3.4.2 Adjust the Height of the Wind Guard .................................. 89
3.4.3 Insert a Net Roll ................................................. 89
3.4.4 Insert the Net .................................................. 90
3.4.5 Move the Pivoted Roller to the Start Position ............................ 91
3.4.6 Insert the Knives ................................................ 92
Table of contents
Baler Wrapper Combination
4900.LE.EN01

AGCO LELY RPC 130 F Specifications

General

Brand	AGCO
Model	LELY RPC 130 F
Category	Industrial Equipment
Language	English