Amazone AmaTron 4 - Universal Terminal

111 pages

Save Page as PDF

To Next Page

To Previous Page

Universal Terminal

Implement information

Function keys

NOTE

The display within the Universal Terminal depends on

the connected implement.

CMS-T-00000236-B.1

D | Operator interface overview | Universal Terminal

MG6010-EN-GB | G.1 | 13.12.2018

Main Page

Default Chapter3
- Table of Contents3
A about this Operating Manual6
- Meaning of the Operating Manual6
- Diagrams6
- Other Applicable Documents9
- Your Opinion Is Important9
B Installation Instructions10
C Amatron 4 Overview11
- Front View11
- Connections12
D Operator Interface Overview13
- Main Menu13
- Application Carousel14
- Map View16
  - Map16
  - Work Menu17
- Universal Terminal18
E Basic Operation19
- Switching the Amatron 4 on and off19
- Switching between the Applications19
- Configure Status Bar21
- Using the Quick-Start Menu21
- Entering Numerical Values22
- Enter Text23
Entering the Basic Settings24
- Activating the Dynamic Button Bar24
- Setting the Date and Time26
- Setting the Display Brightness28
- Showing When the Display Is Touched29
- Activating Swipe Gesture Applications29
Setting up the GPS Receiver31
- Setting up the A100/A101 Receiver31
- Setting up the Ag-Star Receiver32
- Resetting the GPS Receiver to Factory Settings33
Configuring ISOBUS35
Managing Licenses36
Resetting to Factory Settings39
- K Configuring Implements40
- Configuring ISOBUS Implements40
  - Creating Non-ISOBUS Implements41
  - Configuring Non-ISOBUS Implements41
- Renaming Implements43
- Deleting Implements44
- Selecting Implements44
Configuring Tractors46
- Creating New Tractors46
- Changing the Tractor Geometry Data46
- Configuring the Tractor Sensors47
- Renaming Tractors53
- Deleting Tractors54
M Using the Map View55
- Toggling the Button Bar55
- Showing and Hiding the Implement Information56
- Zooming the Map56
- Switching to Bird's-Eye View57
- Focusing on the Vehicle Symbol57
- GPS Drift Correction57
N Map View Configuration59
- Activate Warnings59
- Configuring the Driving Direction Detection59
- Automatically Creating a Safety Zone60
- Configuring the Automatic Zoom61
- Defining the Map Layers62
O Working Without Documentation63
- Creating a New Field63
P Working with Documentation64
- Creating a New Field64
- Importing ISO-XML Job Data65
- Loading ISO-XML Field Data66
- Importing Field Data from a Shape File67
- Creating a New Job68
- Managing Products69
- Managing the Customers72
- Managing Drivers73
  - Exporting ISO-XML Job Data75
Using Part-Width Section Control76
- Overlap, Setting76
- Starting a Recording81
- Terminating a Recording83
R Managing the Field Boundaries84
- Creating the Field Boundary84
- Editing Field Boundaries85
Managing Headlands86
- Creating Headlands86
- Editing the Headlands87
T Marking Obstacles88
Parallel Driving90
- Configuring Parallel Driving90
  - Adjusting the Light Bar Sensitivity90
  - Selecting the Track Line Pattern91
- Creating Track Lines92
  - Creating an A-B Line92
  - Creating Smoothed Contours92
- Creating Beds93
- Using a Light Bar94
Using Automatic Boom Lowering96
W Configuring AUX-N Input Devices98
- Setting up AUX-N Input Devices98
- Managing Preferred Assignments100
  - Confirming the AUX-N Assignment100
  - Changing the AUX-N Assignment100
Using the Universal Terminal105
Y Taking Screenshots106
Z Using the Camera107
Indexes108
- Index108

Amazone AmaTron 4 - Universal Terminal

Table of Contents

Related product manuals