Amazone AmaTron 4 - Selecting Track Line Pattern

111 pages

Save Page as PDF

To Next Page

To Previous Page

5. If the obstacle symbol should be deleted,

select .

6. To set the obstacle symbol,

tap on any spot on the map.

T | Marking obstacles |

MG6010-EN-GB | G.1 | 13.12.2018

Main Page

Default Chapter3
- Table of Contents3
A about this Operating Manual6
- Meaning of the Operating Manual6
- Diagrams6
- Other Applicable Documents9
- Your Opinion Is Important9
B Installation Instructions10
C Amatron 4 Overview11
- Front View11
- Connections12
D Operator Interface Overview13
- Main Menu13
- Application Carousel14
- Map View16
  - Map16
  - Work Menu17
- Universal Terminal18
E Basic Operation19
- Switching the Amatron 4 on and off19
- Switching between the Applications19
- Configure Status Bar21
- Using the Quick-Start Menu21
- Entering Numerical Values22
- Enter Text23
Entering the Basic Settings24
- Activating the Dynamic Button Bar24
- Setting the Date and Time26
- Setting the Display Brightness28
- Showing When the Display Is Touched29
- Activating Swipe Gesture Applications29
Setting up the GPS Receiver31
- Setting up the A100/A101 Receiver31
- Setting up the Ag-Star Receiver32
- Resetting the GPS Receiver to Factory Settings33
Configuring ISOBUS35
Managing Licenses36
Resetting to Factory Settings39
- K Configuring Implements40
- Configuring ISOBUS Implements40
  - Creating Non-ISOBUS Implements41
  - Configuring Non-ISOBUS Implements41
- Renaming Implements43
- Deleting Implements44
- Selecting Implements44
Configuring Tractors46
- Creating New Tractors46
- Changing the Tractor Geometry Data46
- Configuring the Tractor Sensors47
- Renaming Tractors53
- Deleting Tractors54
M Using the Map View55
- Toggling the Button Bar55
- Showing and Hiding the Implement Information56
- Zooming the Map56
- Switching to Bird's-Eye View57
- Focusing on the Vehicle Symbol57
- GPS Drift Correction57
N Map View Configuration59
- Activate Warnings59
- Configuring the Driving Direction Detection59
- Automatically Creating a Safety Zone60
- Configuring the Automatic Zoom61
- Defining the Map Layers62
O Working Without Documentation63
- Creating a New Field63
P Working with Documentation64
- Creating a New Field64
- Importing ISO-XML Job Data65
- Loading ISO-XML Field Data66
- Importing Field Data from a Shape File67
- Creating a New Job68
- Managing Products69
- Managing the Customers72
- Managing Drivers73
  - Exporting ISO-XML Job Data75
Using Part-Width Section Control76
- Overlap, Setting76
- Starting a Recording81
- Terminating a Recording83
R Managing the Field Boundaries84
- Creating the Field Boundary84
- Editing Field Boundaries85
Managing Headlands86
- Creating Headlands86
- Editing the Headlands87
T Marking Obstacles88
Parallel Driving90
- Configuring Parallel Driving90
  - Adjusting the Light Bar Sensitivity90
  - Selecting the Track Line Pattern91
- Creating Track Lines92
  - Creating an A-B Line92
  - Creating Smoothed Contours92
- Creating Beds93
- Using a Light Bar94
Using Automatic Boom Lowering96
W Configuring AUX-N Input Devices98
- Setting up AUX-N Input Devices98
- Managing Preferred Assignments100
  - Confirming the AUX-N Assignment100
  - Changing the AUX-N Assignment100
Using the Universal Terminal105
Y Taking Screenshots106
Z Using the Camera107
Indexes108
- Index108

Amazone AmaTron 4 - Selecting Track Line Pattern

Table of Contents

Related product manuals