EasyManua.ls Logo

Basler DECS-200 - Page 166

Basler DECS-200
181 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Modbus™ Communication DECS-200
7-16
Table 7-15. Information Category C5 (Operating Mode Parameters)
Registers Data Description Access
Data
Format
Note: Read value of register 47562 is always 0.
47563
Switch for changing operating mode via comm. port, to one of three
modes, 0=OFF / 1=PF / 2=var. Holding register 47571 contains
Operating mode status. Note: Read value of register 47563 is
always 4.
RW UI16
47564
Internal tracking status from comm. port: 0 = Off / 1 = On RW UI16
47565
Preposition enable status from comm. port: 0 = Off / 1 = On RW UI16
47566
Raise input enable status from comm. port: 0 = Off / 1 = On RW UI16
47567
Lower input enable status from comm. port: 0 = Off / 1 = On RW UI16
47568
External tracking enable status from comm. port: 0 = Off / 1 = On RW UI16
47569
Limiter Mode options: 0 = both off / 1 = UEL on / 2 = OEL on / 3 =
both on / 4 = SCL / 5 = SCL/UEL / 6 = SCL/OEL / 7 = OEL/UEL/SCL
RW UI16
47570
Voltage matching mode: 0 = Off / 1 = On RW UI16
47571
Operating mode: 0 = Off / 1 = PF Control / 2 = var Control R- UI16
47572
Unit mode status: 0 = Stop / 1 = Start R- UI16
47573
Control mode status: 1 = FCR / 2 = AVR R- UI16
47574
Internal (mode-to-mode) tracking status: 0 = Off / 1 = On R- UI16
47575
Reserved for future C5 data R- UI16
47576
Secondary unit enable status: 0 = primary unit / 1 = secondary unit R- UI16
47577
Load compensation mode status: 0 = Off / 1 = Droop / 2 = Line Drop R- UI16
47578
Load compensation mode selection via comm. ports: 0 = Off/1 =
Droop / 2 = Line Drop. Holding register 47577 contains Load
compensation mode status. Note: Read value of register 47578 is
always 0.
RW UI16
47579
Input for resetting front panel annunciations and latched relay
annunciations: 0 = no change / 1 = reset. Note: Read value of
register 47579 is always 0.
RW UI16
47580
Loss-of-sensing detection enable: 0 = disable / 1 = enable RW UI16
47581
Loss of sensing triggered transfer-to-FCR-mode enable. RW UI16
47582
Under frequency or volts per hertz mode enable. RW UI16
47583
External Tracking enabled: 0 = disabled /1 = enabled RW UI16
47584
Virtual toggle switch for OEL style: 0 = no change, 1 = change
Read back: 0 = summing point, 1 = takeover
RW UI16
47585
OEL option: 0 = Option 1, 1 = Option 2, 3 = Option 3 RW UI16
47586
PF/var option status: 0 = Off, 1 = PF, 2 = var R- UI16
47587 to
47620
Reserved for future C5 data Not
supported
Not
defined

Table of Contents

Related product manuals