28
6. Zone Setup
Zone Setup Default settings
1
3
Speaker
Configuration
Channel Level
The components of the signals output from the various speakers and
the frequency response can be set automatically inside the set by
inputting the existence/absence of combinations of speakers and
their size (corresponding to their low frequency playback capability)
for the speakers used in Zone2 during surround playback in Zone2.
This adjusts the volume of the signal output from the various
speakers and subwoofer used in Zone2.
Front Sp.
Small
Center Sp. Surround Sp.Subwoofer
Small SmallYes
Front L & R Center Surround L & RSubwoofer
12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m)12 ft (3.6 m)
Front L Front R Center Surround R Subwoofer
0.0 dB 0.0 dB 0.0 dB 0.0 dB 0.0 dB
4
Delay Time
This parameter is for optimizing the timing of the sound produced
from the various speakers and subwoofer according to the listening
position in Zone2.
Surround L
0.0 dB
Crossover
Frequency
Set the frequency (in Hz) below which deep bass appearing in the
main channels will be routed to the Zone2 subwoofer.
5
80 Hz
Page
86
2
Subwoofer
Mode
This selects the subwoofer used in Zone2 for playing the low base
sound.
LFE 87
88, 89
90, 91
92
Video Setup
Set the input signal to be output from the Zone2
monitor out terminal.
Video
Convert
Mode
Audio Delay
6
93, 94
7
Zone3/4
Tone/Ch.Lev.
Adjust the tone and channel level of the sound output
from Zone3 and Zone4.
Bass = 0 dB, Treble = 0 dB, HPF = OFF, L/R = 0 dB
95, 96
Set the delay time the sound is synchronized with the
picture which are outputted in Zone2.
AUTO
0 ms 94
Zone3
Zone4
Bass = 0 dB, Treble = 0 dB, HPF = OFF, L/R = 0 dB
5. Advanced Playback
Advanced Playback Default settings
1
2
2ch
Direct/Stereo
Auto Surround
Mode
Turn the audio compression on or off when down-mixing Dolby
Digital signals.
3
Dolby Digital
Setup
The speaker settings can be changed specifically for playing in the 2-
channel direct or stereo mode.
Set the Auto surround mode function.
Basic
OFF
Auto Surround Mode = ON
Page
79
80
81
7. Option Setup
Option Setup Default settings
1
3
Channel Setup
Trigger Out
Setup
The number of channels that you wish to play back in each zone are
assigned to each zone accordingly.
This sets the Trigger Out output for the different input
sources.
If “Zone=Main” is selected, settings can be made for
the individual surround modes.
Main Zone
9.1 CH
Zone2 Zone4Zone3
5.1 CH StereoStereo
4
Volume
Control
AC Outlet
Assign
This sets the AC outlets to on or off for the different
input sources.
5
Page
97~100
2
Power Amp
Assign
Power Amplifiers can be assigned to the various channels according
to your system’s requirements.
Normal
101~105
107, 108
6
Setup
Memory/Lock
– 110, 111
L1
FL
L2
C
L3
SLA
L4
SLB
L5
SBL
R1
FR
R2
–
R3
SRA
R4
SRB
R5
SBR
This sets the volume level of each zone output.
Volume Limit: This sets the upper limit for the
master volume.
Power On Level: This sets the volume level upon
switching on the power of each
zone.
Mute Level: This sets the amount of attenuation
of the audio output when each
zone is muted.
Volume Level: This sets whether the output level
of Zone2 to 4 is fixed or variable.
106, 107
Vol.Limit = OFF, P. On Lev. = LAST, Mute Lev. = FULL
Vol.Lev. = VAR, Vol.Limit = OFF, P. On Lev. = LAST, Mute Lev. = FULL
Vol.Lev. = VAR, Vol.Limit = OFF, P. On Lev. = LAST, Mute Lev. = FULL
Vol.Lev. = VAR, Vol.Limit = OFF, P. On Lev. = LAST, Mute Lev. = FULL
Trigger
Out 1
ZONE = MAIN, All Surround Modes = ON
TUNER PHONO CD
CDR/
TAPE
DVD VDP TV
OFF OFF OFF OFF ON ON ON
VCR-2
ON
DBS VCR-1
ON ON
VCR-3
ON
VCR-4
ON
V.AUX
ON
Trigger
Out 2
ZONE = 2
TUNER PHONO CD
CDR/
TAPE
DVD VDP TV
ON ON ON ON ON ON ON
VCR-2
ON
DBS VCR-1
ON ON
VCR-3
ON
VCR-4
ON
V.AUX
ON
Trigger
Out 3
ZONE = 3
TUNER PHONO CD
CDR/
TAPE
DVD VDP TV
ON ON ON ON ON ON ON
VCR-2
ON
DBS VCR-1
ON ON
VCR-3
ON
VCR-4
ON
V.AUX
ON
Trigger
Out 4
ZONE = 4
TUNER PHONO CD
CDR/
TAPE
DVD VDP TV
ON ON ON ON ON ON ON
VCR-2
ON
DBS VCR-1
ON ON
VCR-3
ON
VCR-4
ON
V.AUX
ON
109, 110
AC Outlet
1~3
ZONE = MAIN
TUNER PHONO CD
CDR/
TAPE
DVD VDP TV
ON ON ON ON ON ON ON
VCR-2
ON
DBS VCR-1
ON ON
VCR-3
ON
VCR-4
ON
V.AUX
ON
This stores the current user settings in the memory.
User
Memory
This sets whether or not to lock the system setup
settings so that thay cannot be changed.
Setup
Lock
Setup Lock = OFF
MAIN
ZONE2
ZONE3
ZONE4
111, 112
4
This parameter is for optimizing the Room EQ with which the audio
signals are produced from the speakers.
Manual EQ
Setup
All Channels and Frequency=0dB 82~84
To Next Page
Loading...
Need help?
General
