Eaton PowerXL Series - Page 209

185
Appendix A—Parameter ID list
POWERXL SERIES VFD MN040010EN—June 2018 www.eaton.com
Menu
Item
No.
Modbus
Register
PROFIBUS EtherNet/IP DeviceNet
Parameter
Description
Data
Type
Length
(in Bytes)
Display
FormatPNU
PNU
SubIndex Class Instance Attribute Class Instance Attribute
P8.12872550 161181168128Motor Control ModeBYTE1x0
P8.2 107 281 0 42 1 10 42 1 10 Current Limit INTEGER 2 x10
P8.3 109 60 0 161 1 82 168 1 30 V/Hz Optimization BOOLEAN 1 x0
P8.4 108 61 0 161 1 74 168 1 31 V/Hz Ratio BYTE 1 x0
P8.5 289 23 0 161 1 75 168 1 32 Field Weakening
Point
INTEGER 2 x100
P8.6 290 24 0 161 1 76 168 1 33 Voltage at FWP INTEGER 2 x100
P8.7 291 23 1 161 1 77 168 1 34 V/Hz Mid Frequency INTEGER 2 x100
P8.8 292 24 1 161 1 78 168 1 35 V/Hz Mid Voltage INTEGER 2 x100
P8.9 293 27 0 161 1 79 168 1 36 Zero Frequency
Voltage
INTEGER 2 x100
P8.102522NANA NANANANANANASwitching FrequencyINTEGER2 x10
P8.1116653410 164122168138Sine Filter EnableBYTE1x0
P8.12 294 626 3 161 1 83 168 1 39 OverVoltage Control BYTE 1 x0
P8.1329829010 161184168140Load DroopingINTEGER2x100
P8.14 299 340 0 161 1 85 168 1 41 Identification BYTE 1 x0
P8.15 1574 20 7 163 1 193 168 1 42 Neg Frequency Limit DOUBLE 4 x100
P8.16 1576 20 6 163 1 194 168 1 43 Pos Frequency Limit DOUBLE 4 x100
P8.17_ 1585 140 0 163 1 199 168 1 44 Frequency Ramp Out
FilterTime Constant
INTEGER 2 x0
P8.18 1591 2406 1 163 1 203 168 1 45 Speed Error Filter
Time Constant
INTEGER 2 x0
P8.19_ 1592 2405 0 163 1 204 168 1 46 Speed Error Band
Stop Frequency
INTEGER 2 x100
P8.20 1593 2400 0 163 1 205 168 1 47 Speed Control Kp INTEGER 2 x10
P8.21 1594 2401 0 163 1 206 168 1 48 Speed Control Ti INTEGER 2 x0
P8.22_ 1595 2400 3 163 1 207 168 1 49 Speed Control Kp At
Field Weakening
INTEGER 2 x10
P8.23_ 1596 2400 1 163 1 208 168 1 50 Speed Control Kp
Below F0
INTEGER 2 x10
P8.24_ 1597 2403 0 163 1 209 168 1 51 Speed Control F0 INTEGER 2 x100
P8.25_ 1598 2403 1 163 1 210 168 1 52 Speed Control F1 INTEGER 2 x100
P8.26_ 1599 2410 0 163 1 211 168 1 53 Speed Control Kp
Below T0
INTEGER 2 x10
P8.27_ 1600 2404 0 163 1 212 168 1 54 Speed Control T0 INTEGER 2 x10
P8.28_ 1601 2406 0 163 1 213 168 1 55 Speed Control Kp
Filter Time Constant
INTEGER 2 x0
P8.29 1602 30 1 163 1 214 168 1 56 Motoring Torque Limit INTEGER 2 x10
P8.30 1603 31 1 163 1 215 168 1 57 Generator Torque
Limit
INTEGER 2 x10
P8.31 1604 36 1 163 1 216 168 1 58 Torque Limit Forward INTEGER 2 x10
P8.32 1605 37 1 163 1 217 168 1 59 Torque Limit Reverse INTEGER 2 x10
P8.33 1607 282 0 163 1 219 168 1 60 Motoring Power Limit INTEGER 2 x10
P8.34 1608 282 1 163 1 220 168 1 61 Generator Power
Limit
INTEGER 2 x10
P8.35_ 1611 2420 0 163 1 223 168 1 62 Acc Compensation
Time Constant
INTEGER 2 x10
P8.36_ 1612 2421 0 163 1 224 168 1 63 Acc Compensation
Filter Time Constant
INTEGER 2 x0
P8.3716202540 1631232168164Flux ReferenceINTEGER2x10
P8.38_ 1621 237 0 163 1 233 168 1 65 Stop State
Magnetisation
INTEGER 2 x10
P8.39_ 1622 132 0 163 1 234 168 1 66 Start Boost Rise Time INTEGER 2 x0
Table 205. DG1 Parameter ID list, continued