Eaton PowerXL Series - Page 233

209
Appendix A—Parameter ID list
POWERXL SERIES VFD MN040010EN—June 2018 www.eaton.com
Menu Item
No.
Modbus
Register
PROFIBUS
Parameter Description
Data
Type
Length
(in Bytes)
Display
FormatPNU
PNU
SubIndex
P3.2.39 1411 2862 1 PID2 Superv Lower Limit DOUBLE 4 x100
P3.2.40 1413 2863 1 PID2 Superv Delay INTEGER 2 x0
P3.3.1 227 276 0 AO1 Mode BYTE 1 x0
P3.3.2 146 460 0 AO1 Function BYTE 1 x0
P3.3.3 149 279 0 AO1 Minimum BYTE 1 x0
P3.3.4 147 277 0 AO1 Filter Time INTEGER 2 x100
P3.3.5 150 274 0 AO1 Scale INTEGER 2 x0
P3.3.6 148 278 0 AO1 Inversion BOOLEAN 1 x0
P3.3.7 173 275 0 AO1 Offset INTEGER 2 x100
P3.4.1 228 276 1 AO2 Mode BYTE 1 x0
P3.4.2 229 460 1 AO2 Function BYTE 1 x0
P3.4.3 232 279 1 AO2 Minimum BYTE 1 x0
P3.4.4 230 277 1 AO2 Filter Time INTEGER 2 x100
P3.4.5 233 274 1 AO2 Scale INTEGER 2 x0
P3.4.6 231 278 1 AO2 Inversion BOOLEAN 1 x0
P3.4.7 234 275 1 AO2 Offset INTEGER 2 x100
P3.5.1 751 2002 0 Logic Function Select BYTE 1 x0
P3.5.2 752 2000 0 Logic Operation Input A BYTE 1 x0
P3.5.3 753 2001 0 Logic Operation Input B BYTE 1 x0
P4.1.1 141 1 8 Keypad Reference INTEGER 2 x100
P4.1.2 116 621 1 Keypad Direction BOOLEAN 1 x0
P4.1.3 114 622 1 Keypad Stop BOOLEAN 1 x0
P4.1.4 1724 NA NA Hand Key Enable BYTE 1 x0
P4.1.5 1679 622 3 Reverse Enable BYTE 1 x0
P4.1.6 2515 NA NA Change Phase Sequence Motor BYTE 1 x0
P4.1.7 1685 NA NA Power Up HOA Select BYTE 1 x0
P4.1.8 2462 NA NA Bumpless Enable BYTE 1 x0
P4.1.9 2423 NA NA Run Delay Time INTEGER 2 x0
P4.1.10 252 620 0 Start Mode BY TE 1 x0
P4.1.11 253 620 1 Stop Mode BY TE 1 x0
P4.1.12 247 117 0 Ramp 1 Shape INTEGER 2 x10
P4.1.13 248 117 1 Ramp 2 Shape INTEGER 2 x10
P4.1.14 249 130 1 Accel Time 2 INTEGER 2 x10
P4.1.15 250 134 1 Decel Time 2 INTEGER 2 x10
P4.1.16 267 639 0 Power Loss Function BY TE 1 x0
P4.1.17 268 151 0 Power Loss Time INTEGER 2 x10
P4.1.18 2444 NA NA 2nd Stage Ramp Frequency INTEGER 2 x100
P4.2.1 254 2227 0 DC-Brake Current INTEGER 2 x10
P4.2.2 263 2222 0 Start DC-Brake Time INTEGER 2 x100
P4.2.3 262 2223 0 Stop DC-Brake Frequency INTEGER 2 x100
P4.2.4 255 2222 1 Stop DC-Brake Time INTEGER 2 x100
P4.2.5 251 2204 0 Brake Chopper Define BYTE 1 x0
P4.2.6 266 2214 0 Flux Brake BOOLEAN 1 x0
P4.2.7 265 2217 0 Flux Brake Current INTEGER 2 x10
P4.3.1 264 43 0 Skip Range Ramp Factor INTEGER 2 x10
P4.3.2 256 41 0 Skip F1 Low Limit INTEGER 2 x100
P4.3.3 257 42 0 Skip F1 High Limit INTEGER 2 x100
P4.3.4 258 41 1 Skip F2 Low Limit INTEGER 2 x100
P4.3.5 259 42 1 Skip F2 High Limit INTEGER 2 x100
P4.3.6 260 41 2 Skip F3 Low Limit INTEGER 2 x100
P4.3.7 261 42 2 Skip F3 High Limit INTEGER 2 x100
Table 206. DH1 Parameter ID list, continued