To Next Page
M
Michael MoralesSep 14, 2025
What to do if Ecolab Water Pump shows Error 206?
- TtammybullockSep 14, 2025
If your Ecolab Water Pump displays Error 206, check USB stick.
What to do if Ecolab Water Pump shows Error 206?
If your Ecolab Water Pump displays Error 206, check USB stick.
What does Error 312 mean on my Ecolab EcoAdd?
Error 312 on your Ecolab Water Pump indicates that the metering head is loose or the diaphragm has a tear. You can resolve this by: * Tightening the metering head fastening screws crosswise (2 Nm). * Replacing the diaphragm if it is torn.
What to do if Ecolab EcoAdd metering pump does not work?
If the metering pump of your Ecolab Water Pump isn't working and there's no display on the ‘EcoAdd’ unit, it could be due to: * A damaged mains cable: Change the mains cable. * Incorrect voltage: Check the mains voltage.
What to do if Ecolab EcoAdd shows Error 406?
If your Ecolab Water Pump displays Error 406, it means very high back-pressure is leading to motor blockage. You should: * Check the metering line for flow. * Check for pressure peaks in the metering lines. * Check back-pressure.
Why is there no metering despite full metering container in my Ecolab EcoAdd Water Pump?
If your Ecolab Water Pump isn't metering even with a full container, consider these possibilities: * The suction lance float might be blocked: Make sure the float is functional. * The suction pipe connector or link connector could be loose or not fully inserted: Tighten the connector, clean the contacts, and ensure the link connector is properly inserted. * The suction lance cable may be defective: Replace the empty signal device.
What to do if Ecolab EcoAdd Water Pump shows Error 203?
If your Ecolab Water Pump displays Error 203, check USB stick.
What to do if Ecolab Water Pump shows Error 201?
If your Ecolab Water Pump displays Error 201, check USB stick.
What to do if Ecolab EcoAdd shows Error 202?
If your Ecolab Water Pump displays Error 202, check USB stick.
What does Error 308 mean on my Ecolab Water Pump?
Error 308 on your Ecolab Water Pump means the start of recording cannot be determined. Data is reset automatically, so no further action is required!
What does Error 303 mean on my Ecolab Water Pump?
Error 303 on your Ecolab Water Pump indicates a fault in totals files. Data is reset automatically, so no further action is required.
General| Brand | Ecolab |
|---|---|
| Model | EcoAdd |
| Category | Water Pump |
| Language | English |
Outlines fundamental safety principles and precautions to be observed during operation.
Defines the intended use of the pump and the consequences of improper use.
Highlights the importance and use of PPE for personnel safety.
General safety notice regarding the use of correct tools for installation and maintenance.
Lists the key features and specifications of the EcoAdd pump.
Explains the hydraulic connections and provides an installation diagram.
Details how to connect the suction and pressure lines, including safety precautions.
Covers the electrical connection procedures and safety precautions.
Provides a detailed explanation of the terminal assignments for pump connections.
Recommends enabling an access code for security and unauthorized access prevention.
Explains how to select the operating mode (Manual, Pulse, Power, Timer) for the pump.
Explains the Timer operating mode with seven-day and interval programs.
Guides on setting up the seven-day program for timed pump operation.
Details how to configure interval programs for timed pump operation with switch-on/off durations.
Provides an overview of all configurable system parameters for the pump.
Explains the importance and function of access codes for pump security and parameter protection.
Allows defining the metering chemical being used, with options for manual input or database selection.
Guides on configuring metering monitoring, including stop pump and deviation settings.
Explains how to activate and configure the metering controller for the pump.
Provides a detailed step-by-step guide for the initial setup and commissioning of the pump.
Details the setup for manual operating mode with the metering enable function activated.
Explains the Pulse operating mode and its two setting options: Concentration and Quantity.
Explains how to set the Power operating mode, using an incoming current signal to control metering capacity.
Guides on setting the variable Power mode with current limits for the pump.
Details the calibration process to be performed after initial installation for optimal performance.
Provides instructions on how to safely switch the pump on and off using the touchscreen.
Refers to Chapter 7.9 for the pump configuration process before operation.
Guides on how to set or change the pump's capacity in Litres during operation.
Explains the procedure for changing the chemical container when an empty signal is detected.
Details the automatic container change process with empty signal detection.
Explains the manual acknowledgement process for container changes when an empty signal is detected.
Explains how to switch between different metering modes (S, M, L, V).
Details the effect of different metering modes on suction duration and metering output.
Guides on selecting the variable metering mode and setting capacity in litres.
Explains how to switch between different operating modes (Manual, Pulse, Power, Timer).
Details how selecting an operating mode affects pump operation based on internal or external signals.
Details how to set the metering rate manually in the Manual operating mode.
Explains the Pulse operating mode for metering based on incoming pulses.
Guides on setting the Pulse mode for concentration-based metering.
Guides on setting the Pulse mode for quantity-based metering.
Explains the Power operating mode where capacity is determined by an incoming current signal.
Guides on setting the variable Power mode with current limits for the pump.
Explains the Timer operating mode with seven-day and interval programs.
Guides on setting up the seven-day program for timed pump operation.
Details how to configure interval programs for timed pump operation with switch-on/off durations.
Explains the process and importance of calibrating the metering pump for accurate flow rates.
Details the step-by-step calibration procedure for the pump.
Explains how to put the pump into maintenance mode for servicing procedures.
Details the steps to enter maintenance mode without requiring an access code.
Explains how to enter maintenance mode when an access code is activated.
Details the procedure for replacing pump suction/pressure valves and metering cartridges.
Details the process for replacing the pump head and diaphragm, including torque specifications.
Lists common faults, their causes, and remedies for troubleshooting the pump.
Presents a table of error codes, their causes, and recommended remedies.
Lists error codes from 100-199, their causes, and remedies, often requiring customer service.
