Fagor 8055 M - Page 459

Programming manual
CNC 8055
CNC 8055i
C.
·M· & ·EN· MODELS
SOFT: V02.2X
·459·
Summary of internal CNC variables.
Speed limit related variables.
Position related variables.
Variables related to the following error.
Variables associated with the live tool.
PLC related variables.
Variables associated with local and global parameters.
Sercos variables.
SSLIMI R R R Spindle speed limit active at the CNC.
SDNCSL R R R/W Spindle speed limit selected via DNC.
SPLCSL R R/W R Spindle speed limit selected via PLC.
SPRGSL R R R Spindle speed limit selected by program.
SPOSS R R R Real spindle position.
Reading from the PLC in ten-thousandths of a degree (within ±999999999)
and from the CNC in degrees (within ±99999.9999).
SRPOSS R R R Real spindle position.
Reading from the PLC in ten-thousandths of a degree (between -3600000
and 3600000) and from the CNC in degrees (between -360 and 360).
STPOSS R R R Theoretical spindle position.
Reading from the PLC in ten-thousandths of a degree (within ±999999999)
and from the CNC in degrees (within ±99999.9999).
SRTPOS R R R Theoretical spindle position.
Reading from the PLC in ten-thousandths of a degree (between 0 and
3600000) and from the CNC in degrees (between 0 and 360).
SDRPOS R R R Position indicated by the Sercos drive.
SPRGSP R R R Position programmed in M19 via program for the second spindle.
SFLWES R R R Spindle following error.
Variable CNC PLC DNC
( section 13.2.13 )
ASPROG R R - Speed programmed in M45 S (within the associated subroutine).
Variable CNC PLC DNC
( section 13.2.14 )
PLCMSG R - R Number of the active PLC message with the highest priority.
PLCIn R/W - - 32 PLC inputs starting from (n).
PLCOn R/W - - 32 PLC outputs starting from (n).
PLCMn R/W - - 32 PLC marks starting from (n).
PLCRn R/W - - (n) Register.
PLCTn R/W - - Indicated (n) Timer’s count.
PLCCn R/W - - Indicated (n) Counter’s count.
PLCMMn R/W - - Modifies the (n) mark of the PLC.
Variable CNC PLC DNC
( section 13.2.15 )
GUP n - R/W - Global parameter (P100-P299) (n).
LUP (a,b) - R/W - Indicated local (P0-P25) parameter (b) of the nesting level (a).
CALLP R - - Indicates which local parameters have been defined by means of a PCALL
or MCALL instruction (calling a subroutine).
Variable CNC PLC DNC
( section 13.2.16 )
SETGE(X-C) W W - Gear ratio and parameter set of the (X-C) axis drive.
SETGES W W - Gear ratio and parameter set of the main spindle.
SSETGS W W - Gear ratio and parameter set of the second spindle.
SVAR(X-C) id R/W - - Sercos variable sercos for the (X-C) axis "id".
SVARS id R/W - - Sercos variable sercos for the main spindle "id".
SSVARS id R/W - - Sercos variable sercos for the second spindle "id".
TSVAR(X-C) id R - - Third attribute of the sercos variable for the (X-C) axis "id".
TSVARS id R - - Third attribute of the sercos variable for the main spindle "id".
TSSVAR id R - - Third attribute of the sercos variable for the second spindle "id".