Home
Gerber
Cutter
Fastrack
Gerber Fastrack User Manual
4
of 1
of 1 rating
89 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
60
Chapter 5, C
utter
Maintenan
c
e and T
roubles
hootin
g
To replace the knife blad
e in the optional knife holder with vernier
1.
Take th
e body
in one
hand a
nd unscrew
the base until
it comes
completely
off.
2.
Pull the ol
d blad
e out of
the h
older
and i
nsert a n
ew
one.
3.
Place the
base on
top of th
e holder
assem
bly and tw
ist it tightly
.
67
69
Table of Contents
Default Chapter
5
Table of Contents
5
Introduction
9
Attentions and Cautions
9
Customer Support
10
Chapter 1 Installation Procedures
12
Preparing the Cutter Environment
12
Unpacking and Setting up the Cutter
13
Cutter Box Contents
14
CUTTER PARTS and COMPONENTS
15
Control Panel
17
Connecting the Cutter to the Computer
18
Serial Interface
18
To Connect the Serial Interface
18
Connecting the Power Cable
19
Installing Knife Holders or Pens
20
Loading Material
21
To Load Cut-Sheet Material
21
To Load Roll Material
23
To Straighten the Material Edge Using the Auto-Sheet-Off Utility
25
Chapter 2 Cutter Controls
26
Understanding the Control Panel
26
Online and Offline Modes
26
Slew Keys
27
ORIGIN Key
27
PAGE Key
28
ENTER Key
28
Menu Keys
29
VALUE Keys
29
General Procedure to Change Settings on the Cutter
30
Tool Selection
31
Toolkind Selection
32
To Change the TOOLKIND
32
Force Selection
33
First Range (15 - 100 Grams)
34
Second Range (110 - 190 Grams)
34
Third Range (200 - 500 Grams)
34
Speed Selection
35
Acceleration Selection
35
Page Length
35
To Set the PAGE LENGTH
36
RESET and CLEAR FUNCTION
37
Available Values/Settings for Parameters - Imperial System
38
Available Values/Settings for Parameters, Metric System
39
CHAPTER 3 CUTTER SETTINGS and SPECIAL FUNCTIONS
40
Introduction
40
Changing the User Language
40
Menu Mode Operation
40
To Plot a Complete Setup Sheet
41
To Plot a Single Line and Change Settings
41
Example of a Fastrack Cutter Setup Sheet
42
General Settings
43
Toolkind Selection
43
To Select a TOOLKIND
43
Sheet-Off / Page Mode
44
Page Commands
44
To Set the SHEET-OFF / PAGE MODE
45
Replot Factor
46
To Set the Replot Factor
46
Smoothing
47
To Change the Smoothing Settings
47
Communication Settings
48
To Change the Serial Communication Settings
49
Language Settings
50
To Change Language Settings
51
Reset to Factory Defaults
51
Chapter 4 Fine Tuning the Cutter
52
Adjusting the Knife Depth
53
To Adjust the Knife Depth of the Standard Tool Holder
53
To Adjust the Knife Depth of the Optional Knife Holder
55
Features of the Optional Knifeholder
56
Setting the Cutting Pressure / Test Squares
57
Setting the Offset
57
Adjusting the Offset
58
Setting up for Pouncing (Punching) Applications
60
Method 1. Pen-Up / Pen-Down Sent by Cutting Software
60
Method 2. Use the Incorporated Pouncing (Punching) Capability of the Cutter
60
To Adjust the Pouncing Tool
61
Performing a Test Cut
62
Generating a Parameter Settings Plot
63
CHAPTER 5 CUTTER MAINTENANCE and TROUBLESHOOTING
64
CLEANING and DAILY MAINTENANCE
64
To Clean the Pressure Rollers and Drive Rollers
64
To Remove Material Particles from the Cutter Blade in a Standard Knife Holder
65
To Remove Material Particles from the Cutter Blade in an Optional Knife Holder with Vernier
65
To Clean the Cutter
66
Parts Replacement
66
To Replace the Cutting Mat
66
To Replace the Knife Blade in the Standard Knife Holder
67
To Replace the Knife Blade in the Optional Knife Holder with Vernier
68
To Replace the Auto-Sheet-Off Knife
69
Troubleshooting
70
To Check the Communication Settings
71
Error Messages
73
Unrecoverable System Errors
73
Recoverable System Errors
76
Communication Errors
77
Language Errors
79
CHAPTER 6 CUTTER OPTIONS and ACCESSORIES
80
OPTIONS and ACCESSORIES for Fastrack CUTTERS
80
CHAPTER 7 MATERIAL COMPATIBILITY and DIMENSIONS
82
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Gerber Fastrack and is the answer not in the manual?
Ask a question
Gerber Fastrack Specifications
General
Brand
Gerber
Model
Fastrack
Category
Cutter
Language
English
Related product manuals
Gerber DCS 1500
176 pages
Gerber DCS 2500
176 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
