GRAPHTEC CE7000 Series - Page 350

I-2
H
HP-GL command ............................ 11-7
HP-GL MODEL EMULATED .................... 11-7
I
I/F ................................... 2-34, 2-35
I/F (LAN) .................................... 9-5
Initial Setting ................................ A-17
Installation space ............................. VII
Interface .................................... 9-2
IP address ................................... 9-7
L
Language .................................. 2-69
LANGUAGE SELECTION ...................... 10-2
LCD contrast setting ......................... 10-11
Length unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
LENGTH UNIT ............................... 10-3
LINK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Loading Media ................................ 2-7
M
Main Specications ............................ A-2
Manual position adjust ..................... 6-2, 6-4
MARK SCAN Mode ............................ 5-8
Media ................................... 2-7, 5-6
MEDIA ................................ 2-34, 2-35
Media sensors ........................ , 1-4, 1-6, 1-8
Media set lever ........................ 1-4, 1-6, 1-8
Media stocker ............................. 1-7, 1-9
Media stopper ............................. 1-7, 1-8
Media that registration mark cannot be detected ..... 5-7
MENU Screen ............................... 2-34
Menu Tree ................................... A-7
Model ID response ........................... 11-7
Mounting the Roll-medium tray .................. 1-10
Mounting the stock shafts ...................... 1-11
Move away the tool carriage ..................... 3-5
Move in steps manually ......................... 3-3
Move the Tool Carriage and Media ................ 3-3
MOVING SPEED .............................. 8-9
N
Netrwork (LAN) Interface connector ........ 1-4, 1-7, 1-9
Network (LAN) interface ........................ 9-3
Nomenclature ................................ 1-4
Normal mode ................................ 2-35
Normal mode setting ......................... 10-10
O
Operation key ............................... 2-31
Options ..................................... A-3
ORIGIN .................................... 2-31
Origin Point Settings When conguring HP-GL ..... 2-67
P
Page Length ................................ 2-65
Panel Cutting ................................ 4-15
Pause key select setting ....................... 10-9
PAUSE/MENU ............................... 2-31
POSITION .................................. 2-32
Positioning ................................... 5-6
Power cable .................................. 1-2
Power switch .......................... 1-5, 1-7, 1-8
Pre Feed of Media ............................ 2-39
Printing the Setting of the Plotter ............... 15-16
Priority of tool condition selection ................ 11-3
Push roller hold-down force switching lever ......... 1-9
Push rollers ........................... 1-4, 1-6, 1-8
Push roller sensors ........................... 10-5
R
Raise or Lower the Tool ........................ 3-2
Reading the error message ................... 15-26
Reading the screen ........................... 2-32
Recommended setting of registration mark ........ 5-10
Registration mark ......................... 5-4, 5-6
Registration Mark ............................. 5-3
Registration mark automatic detection ............ 5-23
Removing the tool ............................. 2-6
Replacing Cutter Blade ........................ 14-3
Reset ....................................... 3-6
Roll media ............................... 2-7, 2-10
Roll-medium tray .......................... 1-3, 1-5
Roll-medium tray guide rail ...................... 1-5
ROTATE ................................... 3-10
RS-232C ................................... 9-10
RS-232C interface ............................. 9-3
RS-232C interface connector ............. 1-4, 1-6, 1-9
S
Selecting Tool Condition ....................... 2-40
Self Diagnostic Test ......................... 15-24
SELF TEST ................................ 15-18
Set the enlarge/shrink scale ..................... 4-8
Setting Adjustment Between the Tools ............ 7-22
Setting and Adjustment of ARMS ................. 5-8
Setting Cut Line Pattern ....................... 7-15
Setting cutting area ............................ 4-2
Setting cutting width ........................... 4-4
Setting Feeding Method ....................... 2-37