GRAPHTEC CE7000 Series - Index

I-1
INDEX
Conrm the results of the cutting test ............. 2-59
Connecting to the Power ....................... 2-30
Continuously move manually .................... 3-3
Control panel .......................... 1-4, 1-6, 1-8
Control Panel ................................ 2-31
Copy ...................................... 4-10
COPY ..................................... 2-31
Cutter blade ................................. 14-3
Cutter blade adjustment magnier ................ 1-2
Cutter Blade Manua ........................... 1-2
Cutter blades ................................. 1-2
Cutter plunger ................................ 1-2
Cutter Plunger Exchange ...................... 14-6
Cutter plunger nomenclature .................... 2-2
Cutting area .................................. 5-6
Cutting groove ......................... 1-4, 1-6, 1-8
Cutting mat ........................... 1-4, 1-6, 1-8
CUTTING PRO ............................. 15-20
Cutting test ................................. 2-56
D
Daily maintenance ............................ 14-2
DATA DUMP ............................... 15-23
Default screen ............................... 2-33
DIAGNOSTICS ............................. 15-25
Display language setting ....................... 10-2
Display Language Setting ...................... 2-69
Display Length Unit Setting. . . . . . . . . . . . . . . . . . . . , 2-70
DISTANCE ADJUST .......................... 7-12
E
Enabling/Disabling the ' : ' and ' ; ' commands ...... 11-5
ENTER .................................... 2-31
Error Messages in GP-GL Command Mode ........ 15-6
Error Messages in HP-GL Command Mode ........ 15-7
ESC ....................................... 2-31
EXPAND .................................... 4-4
F
Fan suction setting ........................... 10-7
Feed Speed for Pre Feed ....................... 8-7
G
Gateway .................................... 9-7
GP-GL command ............................ 11- 4
GP-GL Step Size ............................. 2-68
GP-GL STEP SIZE ........................... 11-4
Grit roller position guide ............ 1-4, 1-6, 2-25, 1-8
Grit rollers ............................ 1-4, 1-6, 1-8
Sign
1, 2, 3, 4 .................................... 2-32
A
About the Default Screen ...................... 2-29
Accessories .................................. 1-2
Accessory case ........................ 1-5, 1-7, 1-9
AC line inlet ........................... 1-5, 1-7, 1-9
Adjusting for the registration mark scan position .... 5-16
Adjusting the blade length ....................... 2-4
Adjustment for cutting out ...................... 2-59
Adjustment for Half Cutting ..................... 2-59
Adjustment of Offset .......................... 2-59
Adjustment on the media ...................... 5-20
Adjustment registration mark ................... 5-16
Adjustment when using plotting pen .............. 2-59
Adjust the blade length ........................ 2-60
Adjust the blade length manually ................ 2-55
Adjust with 2POINTS .......................... 6-2
Adjust with 3POINTS .......................... 6-3
Adjust with 4POINTS .......................... 6-3
ADV. ................................. 2-34, 2-35
Aligning the push roller ........................ 2-25
Angle control ................................ 7-10
AREA ...................................... 2-35
ARMS ................................. 2-35, 5-2
ARMS Error Messages ........................ 15-9
Attaching a tool ............................... 2-5
Automatic detection of registration mark position ..... 5-7
Automatic Pre Feed ........................ 8-4, 8-6
AXIS ALIGNMENT ........................ 6-2, 6-5
B
BARCODE .................................. 2-31
Beep setting ................................ 10-8
Blade application and features ................... 2-4
Blade Manual ................................ 1-2
C
Carrier Sheet ................................ 2-21
Change the cutting condition .................... 3-6
Changing the hold-down force .................. 2-27
Check the lines of registration mark .............. 5-12
CIRCLE RESOLUTION ........................ 11-8
Communication Timeout ...................... 12-10
COND/TEST ........................... 2-31, 2-36
Conrm the Cutting Data ..................... 15-22