To Next PageTo Next PageTo Previous PageTo Previous Page
What to do if HP StorageWorks P9000 - Disk Arrays Storage shows 'Port number invalid' error?
If you encounter a 'Port number invalid' error on HP Storage, delete the failed path. Then, check the specified port number and the cable connection before retrying the operation.
Why does my HP StorageWorks P9000 - Disk Arrays host not reboot after a hard shutdown?
If the host does not reboot properly after a hard shutdown, wait three minutes to allow the disk array's internal timeout process to purge queued commands. If the host restarts while the disk array is processing queued commands, the host may not reboot successfully.
What to do if HP StorageWorks P9000 - Disk Arrays Storage host detects a parity error?
If the host detects a parity error, check the FCA and make sure it was installed properly. Reboot the host.
How to resolve a 'Communication error' on HP Storage?
If you're experiencing a 'Communication error' with HP Storage, where a timeout error occurred in the path between the primary and secondary systems, delete the failed path and retry.
How to fix 'This path was not established' error on HP Storage?
If the HP Storage shows 'This path was not established', delete the failed path. You may need to change the minimum paths setting or delete the secondary system in order to delete the path. After deletion finishes, add the path and the secondary system by using the Add Path or Add DKC command.
What to do if the HP StorageWorks P9000 - Disk Arrays primary system suspended a pair during the initial copy operation?
If the HP Storage primary storage system suspended this pair during the initial copy operation because the data on the S-VOL is not identical to the data on the P-VOL, release the pair from the primary storage system. Clear all error conditions at the primary storage system, P-VOL, secondary storage system, and S-VOL. Restart the initial copy operation using the Paircreate dialog box.
Why did the HP StorageWorks P9000 - Disk Arrays Storage primary system suspend all Cnt Ac-J pairs when powered off?
If the HP Storage primary storage system suspended all Cnt Ac-J pairs because the primary storage system was powered off, no action is needed. The primary storage system automatically restores these Cnt Ac-J pairs when it is powered back on.
What to do if hardware failures cause pairs to be suspended on HP Storage?
If primary or secondary system hardware failures affecting the cache memory and the shared memory of the primary or secondary system may also cause the pairs to be suspended on your HP Storage, remove the hardware blockade or failure according to the SIM. Restore the failed volume pairs (Pairresync). If a failure occurs during execution of the RAID Manager horctakeover command, secondary volumes in SSWS pair status may remain in the master journal. If these volumes remain, execute the pairresync -swaps command on the secondary volumes whose pair status is SSWS (pairresync is the RAID Manager command for resynchronizing pair and -swaps is a swap option. This operation changes all volumes in the master journal to primary volumes. After this operation, restore the volume pairs (Pairresync).
What to do if a Business Copy Z error message is displayed on HP StorageWorks P9000 - Disk Arrays Storage Remote Web Console?
Select the failed volume in the Preview List on the Pair Operation window, right-click to display the menu, and then click Error Detail.
What to do if Remote Web Console hangs, or Business Copy Z operations do not function properly on HP StorageWorks P9000 - Disk Arrays?
Ensure all Business Copy Z requirements and restrictions are met. Also, verify that the storage system is powered on and fully functional. Check all input values and parameters to ensure that you entered the correct information on the Business Copy Z windows, such as S-VOL and T-VOL IDs.
General| Form Factor | Rack-mountable |
|---|---|
| Model | HP StorageWorks P9000 |
| Type | Disk Array |
| Category | Storage |
| Drive Type | SSD, SAS |
| RAID Levels | RAID 0, 1, 5, 6, 10 |
| Host Interface | Fibre Channel, FCoE, iSCSI |
| Connectivity | Fibre Channel, FCoE, iSCSI |
| Cache Memory | Up to 512 GB |
| Controllers | Dual controllers |
| Management Software | HP StorageWorks Command View |
| Redundancy | controllers, power supplies, and fans |
| Operating Humidity | 20 to 80% relative humidity, non-condensing |
Details error messages and recommended actions for part code 0001.
Details error messages and recommended actions for part code 0002.
Details error messages and recommended actions for part code 0003.
Details error messages and recommended actions for part code 1005.
Details error messages and recommended actions for part code 2005.
Details error messages and recommended actions for part code 3005.
