General Information
1-3
Model 2001-TCSCAN:
This is a thermocouple/general pur-
pose scanner card that installs in the option slot of the Model
2002. The card has nine analog input channels that can be
used for high-accuracy, high-speed scanning. A built-in tem-
perature reference allows multi-channel, cold-junction com-
pensated temperature measurements using thermocouples.
Model 4288-1 Single Fixed Rack Mount Kit:
Mounts a sin-
gle Model 2002 in a standard 19-inch rack.
Model 4288-2 Side-by-side Rack Mount Kit:
Mounts two
instruments (Models 182, 428, 486, 487, 2001, 2002, 7001)
side-by-side in a standard 19-inch rack.
Model 4288-3 Side-by-side Rack Mount Kit:
Mounts a
Model 2002 and a Model 199 side-by-side in a standard 19-
inch rack.
Model 4288-4 Side-by-side Rack Mount Kit:
Mounts a
Model 2002 and a 5
¼
-inch instrument (Models 195A, 196,
220, 224, 230, 263, 595, 614, 617, 705, 740, 775, etc.) side-
by-side in a standard 19-inch rack.
Models 7007-1 and 7007-2 Shielded IEEE-488 Cables:
Connect the Model 2002 to the IEEE-488 bus using shielded
cables and connectors to reduce electromagnetic interference
(EMI). The Model 7007-1 is one meter long; the Model
7007-2 is two meters long.
Models 8501-1 and 8501-2 Trigger Link Cables:
Connect
the Model 2002 to other instruments with Trigger Link con-
nectors (e.g., Model 7001 Switch System). The Model
8501-1 is one meter long; the Model 8501-2 is two meters
long.
Model 8502 Trigger Link Adapter:
Allows you to connect
the Trigger Link of the Model 2002 to instruments that use
the standard BNC (In/Out) external triggering technique.
Model 8530 IEEE-488 to Centronics Printer Adapter
Cable:
Translates the IEEE-488 connector pinout and signal
level to a Centronics termination. This permits a standard
Centronics parallel printer to be connected to a Model 2002
in TALK-ONLY mode.
Model 8605 High Performance Modular Test Leads:
Con-
sists of two high voltage (1000V) test probes and leads. The
test leads are terminated with a banana plug with retractable
sheath on each end. (Each Model 2002 is shipped with one
set of these test leads.)
Model 8606 High Performance Probe Tip Kit:
Consists of
two spade lugs, two alligator clips, and two spring hook test
probes. (The spade lugs and alligator clips are rated at 30V
RMS, 42.4V peak; the test probes are rated at 1000V.) These
components are designed to be used with high performance
test leads terminated with banana plugs, such as the Model
8605 High Performance Modular Test Leads.
The following test leads and probes are rated at 30V RMS,
42.4V peak:
Models 5805 and 5805-12 Kelvin Probes:
Consists of two
spring-loaded Kelvin test probes with banana plug termina-
tion. Designed to be used with instruments that measure 4-
terminal resistance. The Model 5805 is 0.9m long; the Model
5805-12 is 3.6m long.
Model 5806 Kelvin Clip Lead Set:
Includes two Kelvin clip
test leads (0.9m) with banana plug termination. Designed for
instruments that measure 4-terminal resistance. A set of eight
replacement rubber bands for the Model 5806 is available as
Keithley P/N GA-22.
Model 8604 SMD Probe Set:
Consists of two test leads (3ft),
each terminated with a surface mount device “grabber” clip
on one end and a banana plug with retractable sheath on the
other end.
Model 8610 Low Thermal Shorting Plug:
Consists of four
banana plugs mounted to a 1-inch square circuit board, inter-
connected to provide a short circuit among all plugs.
Model 8611 Low Thermal Patch Leads:
Consists of two
test leads (3ft), each with a banana plug with a retractable
sheath at each end. These leads minimize the thermally-
induced offsets that can be created by test leads.
Model 8612 Low Thermal Spade Leads:
Consists of two
test leads (3ft), each terminated with a spade lug on one end
and a banana plug with a retractable sheath on the other end.
These leads minimize the thermally-induced offsets that can
be created by test leads.
Model 8680 RTD Probe Adapter:
This adapts RTDs with
terminated and unterminated cables to instruments with
banana jacks for measuring 4-terminal resistance. It has a 4-
pin “T”-style connector and a 4-pin screw terminal block.
Model 8681 Miniature RTD Surface Probe:
This is a low
cost platinum 4-wire-RTD with unterminated wires. It is
designed to measure the temperature of flat surfaces or free
space.
M
odel 8693 General Purpose/Immersion RTD Probe:
This probe has a platinum RTD sensor. It is designed for
immersion in liquids as well as other general purpose
applications.
To Next Page
Loading...
Need help?
General
