[SOURce:]ARB:SEQuence:STEP:CURRent:RAMP:END:TIMe <value>, <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:CURRent:RAMP:END:TIMe? [MIN|MAX,] <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:VOLTage:RAMP:END:TIMe<value>, <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:VOLTage:RAMP:END:TIMe? [MIN|MAX,] <step#>, (@<chanlist>)
Specifies the time in seconds, after the ramp completes, that the ending current or voltage level
persists for Arb sequence steps.
Parameter Typical Return
0 – 262.144 | MIN | MAX, *RST 0 <end time>
Step 0 - 99, *RST 0 (none)
Programs an end time for the current ramp: ARB:CURR:RAMP:END:TIM 2,(@1)
Programs an end time for the voltageramp:ARB:VOLT:RAMP:END:TIM 2,(@1)
Programs an end time for step 0: ARB:SEQ:STEP:CURR:RAMP:END:TIM 2, 0,(@1)
[SOURce:]ARB:CURRent:RAMP:RTIMe <value>, (@<chanlist>)
[SOURce:]ARB:CURRent:RAMP:RTIMe? [MIN|MAX,] (@<chanlist>)
[SOURce:]ARB:VOLTage:RAMP:RTIMe<value>, (@<chanlist>)
[SOURce:]ARB:VOLTage:RAMP:RTIMe? [MIN|MAX,] (@<chanlist>)
Specifies the rise time of the ramp in seconds. Referenced to t1 in the Ramp diagrams.
[SOURce:]ARB:SEQuence:STEP:CURRent:RAMP:RTIMe <value>, <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:CURRent:RAMP:RTIMe? [MIN|MAX,] <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:VOLTage:RAMP:RTIMe <value>, <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:VOLTage:RAMP:RTIMe? [MIN|MAX,] <step#>, (@<chanlist>)
Specifies the rise time of the ramp in seconds for Arb sequence steps.
Parameter Typical Return
0 – 262.144 | MIN | MAX, *RST 1 <risetime>
Step 0 - 99, *RST 0 (none)
Programs a rise timefor thecurrent ramp: ARB:CURR:RAMP:RTIM 10,(@1)
Programs a rise timefor thevoltageramp: ARB:VOLT:RAMP:RTIM 10,(@1)
Programs a rise timefor step 0: ARB:SEQ:STEP:CURR:RAMP:RTIM 10, 0,(@1)
[SOURce:]ARB:CURRent:RAMP:STARt[:LEVel] <value>, (@<chanlist>)
[SOURce:]ARB:CURRent:RAMP:STARt[:LEVel]? [MIN|MAX,] (@<chanlist>)
[SOURce:]ARB:VOLTage:RAMP:STARt[:LEVel] <value>, (@<chanlist>)
[SOURce:]ARB:VOLTage:RAMP:STARt[:LEVel]? [MIN|MAX,] (@<chanlist>)
Specifies the initial current or voltage before the ramp occurs. Referenced to I0 and V0 in the Ramp
diagrams.
Keysight N6705C Operating and Service Guide 245
7 SCPI Programming Reference
To Next Page
Loading...
