Effect
147
2. Routing
You can use up to two channels (MFX1 and 2) for the Master
Effects in any mode other than in Sampling mode. (You can-
not use the Master Effects in Sampling mode.) If you are not
using any Insert Effects in any mode, the Master Effects send
levels are determined by the “Send Level 1/2 (MFX2)”
parameters specified independently for the oscillators (Pro-
gram), timbres (Combination), tracks (Multi), and audio
inputs (Global). For example, you can apply substantial
reverberation to a piano sound assigned to the timbre and
tracks, a small amount of reverberation to the strings sound,
and no reverberation to the bass sound. If you are using the
Insert Effects, set the “S1 (Send1(MFX1))” and “S2
(Send2(MFX2))” parameters for the post-IFX signals.
2–1. Program mode
The PROG 7.1–1a MFX Send parameters “Send 1” and
“Send 2” or the PROG 7.2–1a “S1 (Send 1 (MFX1))” and “S2
(Send 2 (MFX2))” parameters that follow IFX1–5 determine
the send levels to the master effects.
The PROG 7.1–1a MFX Send “Send 1” and “Send 2” settings
are used when “BUS Select” is set to L/R or Off. Each can be
set for oscillator 1 and 2.
The PROG 7.2–1a “S1 (Send 1 (MFX1))” and “S2 (Send 2
(MFX2))” settings that follow IFX1–5 are used when “BUS
Select” is set to IFX1–5. If the insert effects are chained (con-
nected in series), the “S1 (Send 1 (MFX1))” and “S2 (Send 2
(MFX2))” that follows the last-connected IFX will be used.
If “BUS Select” is 1, 2, 3, 4, 1/2, or 3/4, the oscillator will be
directly output to AUDIO OUTPUT (INDIVIDUAL)1, 2, 3, 4
(
☞”Individual Output”). Send levels 1/2 will be ignored,
and the master effects will not be applied.
Send Level 1 can be controlled by MIDI Control Change
CC#93 and Send Level 2 can be controlled by MIDI
Control Change CC#91 on MIDI Global channel “MIDI
Channel” (GLOBAL 2.1–1a). At this time, the actual
send level uses the value of the Send 1 and 2 settings for
Oscillators 1 and 2, multiplied by the Send Level 1 and
2 values received via MIDI.
If the program “Oscillator Mode” (PROG 2.1–1a) is Drums,
the “USE DKit Setting” (PROG 7.1–1b) will be used.
If this is checked, the setting for each key of the selected
drum kit will be used. The drum instrument for a key whose
drum kit “BUS (Bus Select)” (GLOBAL 5.1–3a) parameter is
set to L/R or Off will use the “S1 (Send 1 (MFX1))” and “S2
(Send 2 (MFX2))” (GLOBAL 5.1–3a) settings. If IFX1–5 is
used, the “S1 (Send 1 (MFX1))” and “S2 (Send 2 (MFX2))”
(PROG 7.2–1a) after passing through IFX1–5 will be used.
If this is not checked, the “Send 1” and “Send 2” (PROG 7.1–
1a, MFX Send) settings or the “S1 (Send 1 (MFX1))” and “S2
(Send 2 (MFX2))” (PROG 7.2–1a) settings after passing
through IFX1–5 will be used for all drum instruments. (This
is the same as when “Oscillator Mode” is Single or Double.)
2–2. Combination, Multi mode
Use “S1 (Send 1 (MFX1))” and “S2 (Send 2 (MFX2))” (7.1–
1(2)a) for timbres (Combination) and tracks (Multi) to set the
Send level for each timbre and track. As with Program
mode, if “BUS Select” is set to L/R or Off, “S1 (Send 1
(MFX1))” and “S2 (Send 2 (MFX2))” become effective. In this
case, the actual send level will be the setting of the program
(PROG 7.1-1a) used by the timbre/track multiplied by the
send level you specify here.
– Send level –
For example, if a Program’s “OSC1 Send1” is set to 127,
“Send2” set to 064, “OSC2 Send1” set to 064, “Send2” set to
127, a Combination’s “Send1” set to 064, and “Send2” set to
127, the actual send levels of the combination are calculated
as follows:
OSC1 Send1=127 (100%)*064(50%)=064(50%)
OSC1 Send2=064 (50%)*127(100%)=064(50%)
OSC2 Send1=064 (50%)*064(50%)=032(25%)
OSC2 Send2=127 (100%)*127(100%)=127(100%)
If IFX1–5 is selected for “BUS Select”, use the “S1
(Send1(MFX1))” and “S2 (Send2(MFX2))” parameters for the
post-IFX signals.
If 1, 2, 3, 4, 1/2, or 3/4 is selected instead, these settings are
ignored and the Master Effect is not applied.
Send Level 1 responds to MIDI Control Change CC#93,
and Send2 Level responds to MIDI Control Change
CC#91. If “Send1 (MFX1)” and “Send2(MFX2)” for
each timbre/track are effective, the parameter will be
controlled on the MIDI channels set for the correspond-
ing timbres and tracks. If the “Send1(MFX1)” and
“Send2(MFX2)” parameters for the post-IFX1–5 signals
are effective, they can be controlled on the MIDI chan-
nels assigned to IFX1–5.
To Next Page
Loading...
