MIMAKI CJV150-107 - Page 3

© 2014 MIMAKI ENGINEERING CO.,LTD.
Maintenance Manual Contents R.1.0 P.1
MAINTENANCE MANUAL > Maintenance Manual Contents
Model CJV150/300 Issued 2014.09.15 Revised F/W ver. 1.00 Remark
Maintenance Manual Contents
1.0
Rev.
1 Operating Principle
1.1 Basic Operation
1.1.1 Mark Detection
1.2
Maintenance Function
1.3
Ink System
1.3.1 Configuration
1.3.2 Ink System Error Monitoring
1.3.3 Supply Cartridge Control and
Selection
1.3.4 Cartridge LED Control
1.3.5 Supply Valve Control
1.3.6 Monitoring of the Amount of
Remaining Ink
1.3.7 Use-up Cleaning
1.3.8 Ink Suction and Discharge Control
1.3.9 Initial Filling
2 Electrical Parts
2.1
Block Diagram
2.1.1 Connection Diagram Inside the Main
Body
2.2
Operation Explanation
2.2.1 Operation Explanation
2.3
Circuit Board Specifications
2.3.1 EPL2 Main PCB Assy
2.3.2 SL2H PCB Assy.
2.3.3 COM16 IO PCB Assy./COM32 IO
PCB Assy.
2.3.4 AC PCB Assy
2.3.5 Color LCD PCB Assy.
2.3.6 RGB LED PCB Assy
2.3.7 Encoder PCB Assy
2.3.8 Mini Memory PCB Assy
2.3.9 Mark Sensor PCB
2.3.10 CART IO PCB Assy.
2.3.11 CG common slider PCB Assy
2.3.12 Pen Encoder PCB Assy.
2.3.13 Mark Pointer Assy.
2.3.14 240W42V Power Supply Assy.
2.3.15 15W5V Power Supply Assy.
3 Workflow
3.1 Ink Related Parts
3.1.1 Replacement of the Head Unit
3.1.2 Replacement of the Cartridge Assy
3.1.3 Replacement of the Wiper Unit
3.1.4 Replacement of the Wiper Cleaner
Assy.
3.1.5 Replacement of the Selective path
Assy.
3.1.6 Replacement of the Cap Head Assy.
3.2 Driving Parts
3.2.1 Replacement of the X-axis Motor
3.2.2 Replacement of the Y-axis Motor
3.2.3 Replacement of the Y Drive Belt
3.2.4 Replacement of the Linear Encoder
Scale
3.2.5 Replacement the GR Roller Assy
3.3 Electrical Parts
3.3.1 Replacement of the EPL2 Main PCB
Assy
3.4 Cutting Related Parts
3.4.1 Replacement of the Pen Assy and
LED Pointer
3.4.2 Replacement of the Mark Assy
3.4.3 Replacement of the Cutter Assy
4 Adjustment Items
4.1 Operation Matrix
4.2 Adjustment Function
4.2.1 AVERAGING 34 ADJUST
4.2.2 STAGGER ADJUST
4.2.3 DROP.POS
4.2.4 REPLACE COUNT
4.2.5 DEFAULT SET
4.2.6 CAPPING
4.2.7 ADJUST WIPER
4.2.8 HEAD WASH
4.2.9 MAINT. WASH
4.2.10 HEAD ID
4.2.11 SERIAL No.
4.2.12 DEALER No.
4.2.13 FEED COMP.2
4.2.14 EDGE ADJUST
4.2.15 POINTER OFFSET
4.2.16 TIME SET
4.2.17 ANGLE ADJUST
4.2.18 LAN CONFIG
4.2.19 ZI COMMAND
4.2.20 PEN NO. ASSIGN
4.2.21 PEN STROKE
4.2.22 400 mm SQUARE
4.2.23 PEN PRESSURE
4.2.24 PHOTO SENSOR
4.2.25 GR/PR POSITION
4.2.26 PRINT/CUT POS.
4.3 Mechanical Adjustment